Wire Strain Relief for Printrbot Simple Metal Heat Bed Modification 3d models

... the two anchor links with their tabs on the same side of the chain. One end should be secured to the heat bed using a wire tie, replacing the original cable. ...The other end is attached to the metal base using double-sided tape for added stability.

icotekcable managementstrain relief

My biggest complaints about this machine is the lack of strain relief, no wire management, and lack of grommets for wires passing through metal enclosures. The heated bed connector and cable is also inadequate for the application. I would be happy...

Zonestar Z6FB Bed Cable Strain Relief

... The sliced version is designed for a 300x300 bed with minimal support needed. Print time is approximately 35 minutes. Version one features thin walls and somewhat flexible design. ...Version two boasts thicker walls and a more rigid construction.

A straightforward solution for adding heated bed cable strain relief requires just one simple component: a nylon 1/8 single hole clamp. This versatile part is also used for bed reinforcement, but with a twist - instead of inserting it from the...

A mount for your Printrbot Simple Metal that will hold 4 strips of LED Light Strips (6 sections) for illuminating your workspace. Resting above the Extruder plate, with overhangs in the back that keep it firmly secured. Based on the original...

The space under the PrintrBot Simple Metal is sufficient for the length and width of the Arduino/RAMPS setup. However, the stock height of this controller exceeds the available space. ...To rectify this issue, I made three modifications: 1) replaced...

I'm not a CAD expert, but Tinkercad has been a game-changer for me; it enables me to create simple yet effective tools that streamline my workflow without unnecessary flair. This particular design simply slips over the aluminum bed support bar...

I needed a way to ease the tension on the cable because the wire kept twisting against whatever I used to prop up the pedals and keep them from shifting.

Soldering wires to a LED strip requires strain relief to avoid soldering pads to break of the LED strip. This is realized with a simple clip on the back side of the LED-aluminium profile.Suitable for up to 5 wires (e.g. ...RGBW) with 0.5mm²...

Here is a strain relief for heated bed cables of the FLSun Cube. A zip tie is used to secure it to the bed frame, with a small hole drilled through the frame to pass the tie. No support is needed to print this part. The main web page for this object...

Print Settings: Printer Brand: Printrbot Printer: Printrbot Simple Metal Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: I printed with bridge nylon, and ABS or other materials that can withstand being next to the hot ends should work...

Switching heated bed orientation, needed new strain relief. This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/5x5UBh0PHH6

This is a raspberry pi camera case and stand mounting securely on the left side of a printrbot simple metal model. I am currently designing an efficient hidden wiring system for the PSM and this camera stand is just one component in my project. As...

I whipped up a speedy design in Tinkercad for a super simple strain relief that's perfect for the heated bed of my trusty Tronxy XY-3. This baby prints out in under 30 minutes and requires just two M3 bolts, each a whopping six millimeters long. ...The...

Attach your Raspberry Pi directly to your Printrbot Simple Metal's frame, using a clip that attaches from underneath. Select a 17mm clip designed for use with the Raspberry Pi sleeve case at: http://www.thingiverse.com/thing:604915 . Choose the 14mm...

## Installation - Remove the two big wheels on the rear used for leveling the bed - Pull the bed up and remove the original cable strain relief - Put the new one in its place - Use the two holes to fix the cables in place with a cable tie. Make sure...

This creation is brought to life by the power of Tinkercad. ...Make your mark on its digital canvas at https://www.tinkercad.com/things/tbXhA6xjgBz.

Printrbot Simple Metal Extruder 40mm Fan Holder. A metal housing designed to shield a jet exhaust fan, unlike my previous attempt which unfortunately underperforms. Printed in white plastic and meticulously detailed with a #2 pencil lead. My...

Cable strain relief for the heated bed cable on Artillery Sidewinder X1 v4 printers. This design was inspired by Skinah's "Artillery Sidewinder X1 ac bed heater strain relief and cable chain" from Thingiverse. Unfortunately, that one did not line...

I didn't find a design in OpenSCAD for a heated bed strain relief for a Two Trees Sapphire Pro, so here is mine. Haven't printed it yet - printer is still busy. The strain relief attaches to one of the Z linear bearing housings. It is clamped...

I replaced my Printrbot Simple Metal's imperial 1/4" Z-rod and z-nut due to failure of the Delrin z-nut, as Printrbot no longer sells this part. I needed a mount for an 8mm trapezoid's brass z-nut on the printrbot. This mount positions the z-nut...

So I combined the mount arm with ekidd's generalised webcam mount to create a sturdy press-fit swivel mount for adding Jerware's RasPi camera enclosure to your Printrbot Simple Metal. I took the initiative to reinforce the transition between the bed...

It even has tappable (can use a metal M3 bolt to tap) holes for mounting the easily removable spool holder that printrbot provides an stl file for.https://www.youmagine.com/designs/printrbot-simple-filament-spool-holder The spool holder is shown...

Here is the text rewritten in American English: A simple yet sturdy support for the mini USB cable that plugs into the Printrbot mainboard. The base features two integrated structures that securely attach it to the printer's metal base. ...Feel free to...

Note: due to the general abandonment of Thingiverse and recent security issues, I've moved my designs to the Prusa Printers site: https://www.prusaprinters.org/social/171511-djos_1475/prints...

I upgraded my blower part cooling fan to a 50x15 model and attempted to use the official Printrbot blower fan shroud, but its straight airflow made my hotend unstable when heating the heat bed. To improve this setup, I modified the Printrbot version...

The fan shroud for the Printrbot Simple Pro didn't perform as one would expect because with original design it was blowing straight at the hotend nozzle. When the fan was on above 75% it would cool the nozzle to the degree that it would override the...

This versatile cable strain relief and bed restraint is designed specifically for the ** CR-10s 4 **, but its compatibility extends to other CR-10 printers as well. It seamlessly integrates with stock hardware. The modification features a press-fit...