ammonite 3d model

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

I printed the nuts and locks in a bright colour to highlight their function and make them easy to find if they were to fall off. I have uploaded a 3mf file containing all the parts in the correct orientation on the build plate, however you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 79...

Then it becomes matter of swapping the 5 tubes that lead to the MMU2S, but not to refeed the buffers each time.The model consists of two parts: a connector which is screwed between the upper and lower part of the body, and a bracket that holds two...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons?</p><p>Feel free to remix it as you wish. It would be nice if you upload the...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

If you leave in the comments what brands you've confirmed worked I will update the description.See the HOT2Handle for a smaller version that also fits directly into the cup holders of many car models. (<a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 45...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

OpenSCAD is a script-based modeling software specifically created for projects like this that need to be customizable.If you're new to the program, it may look strange at first, but most of the work is just typing values into a form or selecting...

Future models could have built in cable management. There is a space in the box for mounting the arduino pro micro and also the MCP23017 I/O expander. The buttons are wired as a 4 x 10 matrix to give the 40 buttons so 14 pins are needed (hence...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small customization to the model. More to come as I sort this out, but the files themselves are ready...

If you are worried about fit and don't want to waste filament, a test print that's just a few layers tall will work well.AdjustmentsThis model was designed in OnShape, which makes it easy to adjust the design; just click here to copy and modify the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

I built the flat surface of the skirt with ParametricPlot3D, then intersected it with a lattice-like model, then I utilized those tables to make two ParametricPlot3D tubular surfaces, which I then pieced together using the Show command to make the...

Partner's link: https://www.printables.com/model/299133-ghost-themed-clipLesson Plan and Activity:With a partner, we were tasked to recreate a provided ghost clip using SOLIDWORKS. Together, we not only had to get our design as identical as possible...