anet a8 acrylic frame 3d models

A simple spring bushing designed to prevent warping and bending of the Anet A8 hotbed springs is easily created using an OpenSCAD file, allowing for adjustable dimensions that make it generally applicable. The screw fits snugly into place, which I...

... for valuable design input. I adjusted the location on the hole in Circuit Board Cover 2 to match the reset switch button perfectly on the circuit board. Good luck with your print! Print Settings Printer: ANET A8 Rafts: No Supports: No Infill: 20%

... positioned at the tip of the bolt to evenly distribute pressure on the Y plate, allowing for easy scaling down in the slicer if necessary. Alternatively, users can opt for the low-profile version, which fits seamlessly with the ANET A8 machine.

I required an expedient bowden mount for my Anet A8 after acquiring my titan extruder and wishing to abandon the direct drive configuration. I modified the NEMA 17 motor mount and appended a few "v" shapes on the bottom of the mount (they will be...

This mount can support both the 50mm stock fan blower from the Anet A8 and the inductive sensor SN-04. The blower height can be adjusted and I also redesigned the nozzle. ... These are the offsets inside the Skynet firmware: **#define...

Recently purchased an Anet A8 Plus for a budget-friendly Cartesian setup, which arrived in semi-assembled condition with one of the bed bearing holders cracked. To remedy this situation, I designed and printed a replacement part to ensure seamless...

this is another filament guide to be placed over the extruder.it differ from the other because of the scerw slots which allows it to be installed in most anet a8 versions. ...also it is the closest to the extruder hole i have ever printed.</p><p>the...

Add a script for each layer of your print in your slicing software: G90 ; M108 8000 ; G0 E-10 ; G1 Y200 ; G1 X-33 ; This script is for anet A8, it will move the bed always in the same spot, then the X axis will home to click on the earbuds. ... ...

A replacement front brace for Anet A8, crafted with precision. The STL file was carefully rotated 45 degrees to ensure seamless integration onto the build plate. To guarantee accurate installation, a distinctive marking is now featured on the front...

Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: .2 - .3 Infill: 20-50% Post-Printing Mounting is a breeze, as no additional screws are needed; it simply attaches to the fan/extruder using existing screws. ...Printing time...

The a8 was printed with 60/120 stability, taking just 0.2 seconds to complete. It fits perfectly and finishes in only three hours. ...I also made some minor adjustments to the torch so that the M3 screws fit better afterwards.

I used vernier calipers and feeler gauges to get the exact height needed for my A6, this should be the same for your A6, but definitely not for the A8, hence I put Anet A6 on the actual model. I would definitely lay the model flat (rotate y 90...

... Anet A3 kit in one neat location. ...This design doesn't include a slot for side cutters, as I learned a valuable lesson after breaking them. The mounting point is securely attached to the frame beneath the PCB and held fast with the original screws.

I designed this to position the extruder of my A8 above the display as i wanetd to mount the spool holder on the wall behind the printer. Printed the first test in .3mm resolution (see pictures) but the part fittet so nice that i kept it. Depending...

I set out to position my A8 extruder above the display exactly as planned, with the spool holder firmly attached to the wall behind the printer. With a successful first test printed in .3mm resolution, I was pleased to see that the part fit...

... any issues with the fit of the tabs on your printer. Here are the print settings used for this cover: Printer: Anet A8 Rafts: No Supports: No Resolution: .4 layer height for a 3-hour build time; .2 layer height takes around 6.5 hours Infill: 0%

https://www.myminifactory.com/object/gopro-support-anet-a6-a8-56116 This design includes all the necessary parts and instructions to get you up and running in no time. Simply print out the support material, assemble it according to the instructions,...

Four of these pieces are used to secure the glass to the heated bed of my anet a8, avoiding the usage of binder clips. The usage of binder clips for me was a problem for me: the home of the head is outside the printing area (when homing some binder...

Edited 2019 01 28 Added version 4 - Semicircular 6 Way Edited 6/12/2018 Added Version 3 4 Way Fan Duct for Anet A8 I'm Not Sure This is Better Than All the Other, but I Like "Squared" Designs. I Am Using It Without Issues Since I Printed. To...

Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: grid, 20% Notes: Be sure to read the PDF carefully! Use 30% grid support in Cura Engine within Repetier Host for minimal warping of the plate, which is approximately...

The reason is that it's too low for an Anet A8 and crashes the bed on the backplate. DO NOT OVERTIGHTEN, if you fasten it too well it won't be a smooth run, similar to the stock bearings. The print setting is straightforward: 0.4 nozzle 2 wall...

edited 2019 01 28 added version 4 - semicircular 6 way edited 6/12/2018 added version 3 4 way fan duct for anet a8 i am not sure this is better than all the other, but i like "squared" designs. i am using it without issues since i printed to...

... piece. The spool holder arms slot into the brackets. The spool bolt and nut...that should be obvious. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% 3D hexagonal (Slic3r) Category: 3D Printer Accessories

Additionally, I use the Anet A8 Extruder Fan Spacer by AZDawg (http://www.thingiverse.com/thing:1798669), which I customized so the fan sits flush on the aluminum block. Both parts are screwed together with one 3x40mm screw and two 3mm nuts. The...

A mount to hold a BL Touch Sensor to an Anet A8I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then screwed back in place over...

Spool Holder For Prusa i3 With Acrylic Frame - Works With 1/4" Threaded Rod. ... Print Settings: Printer Brand: Printer Model: Folger Tech Prusa i3

In my opinion, I think many confuse the helical spindle of the Anet A8 with the old screw that came in the first Prusa I3, since that screw had no other function than to screw but it was used as a spindle, causing countless problems of misalignments....

If you're interested in more Anet A8 projects, check out the following links: The One - Anet A8 - Universal Spool Holder https://www.thingiverse.com/thing:2456038, Anet A8 Easy Magnetic Extruder Access Mod (8x2 magnets)...

I am working with Marlin to get a 2.0 file optimized for the Anet A8 and A6. Version 2.0 is still in development, and I'm waiting for a more stable version to upload. However, this file will still work perfectly on these printers with other Marlin...

It is compatible with the Anet Hulk Frame Brace, which can be found at https://www.thingiverse.com/thing:2189694. For part two, it needs to be rotated 180 degrees and printed with support. You will need a longer screw (M3 - 25mm) and a shorter...