anet a8 acrylic frame 3d models

I've been searching for a solution to attach two filament coils simultaneously on my Anet A8 for swift filament changes. The filament holder from DBaysinger arrived and proved to be a game-changer. I discovered that this accessory can be installed...

Bearing blocks for Anet A8 Y axis with sintered bushes 12mm x 8mm x 12mm. A bearing block is designed specifically to secure the descender of the Y axis. The noise level has significantly decreased with these bearings, and the heatbed suspension...

... printer, which will significantly enhance its performance. I'll be sure to update the files and photos as I make changes, so stay tuned for further updates. Print Settings Printer: RepRap Anet A8 Rafts: No Supports: No Resolution:.2 Infill: 50%

... Support for the Belt may be Required the Called Plus Piece, this Piece Serves as a Template to Make the Joint of the Floor. Between the Motor and the Support No Seal is Needed, although it Appears in the Photo. Print Settings Printer: Anet A8

I was right in the middle of rebuilding my Anet A8 when disaster struck - both belt mounts snapped clean off. So, I spent some quality time designing and printing this (big thanks to my trusty backup Tronxy X1). You'll get a chance to see how it's...

... compatibility is ensured by the presence of two nut holes on either side. You also have the option to forego using a screw altogether – no judgment here! Print Settings: Printer: Anet A8 Rafts: Not applicable Supports: Irrelevant Infill: 20-35%

**Print Settings** * Printer: Anet A8 * Rafts: Doesn't matter * Supports: Yes * Infill: 30 **Overview and Background** The Spoll holder is being tested for its effectiveness. **Lesson Plan and Activity** None. ... **Materials Needed** PLA or ABS,...

Another Y-Belt Tensioner for the Anet A8 printer, inspired by the design at http://www.thingiverse.com/thing:1959208. This model utilizes a M4 Hex-Head Screw to achieve tension and features a plate that distributes pressure evenly across its surface....

Problem Identification ---------------------- If you own an older Anet A8 board, chances are you can't adjust stepper currents for all axes, only the z-axis steppers. For more information, visit...

Printed Parts: 1) A8 Dual Extruder - V3.3 Carriage Mounting (Note: This part may require PETG) 2) A8 Dual Extruder - V3 Part Cooling Duct 1) A8 Dual Extruder - V3.3 Top Left 1) A8 Dual Extruder - V3.3 Top Right Optional Parts: 1)...

Printed Parts 1) A8 Dual Extruder - V3.3 Carriage Mounting (This part may need to be PETG) 2) A8 Dual Extruder - V3 Part Cooling Duct 1) A8 Dual Extruder - V3.3 Top Left 1) A8 Dual Extruder - V3.3 Top Right Optional Parts 1) X_Axis_Cable_Tray_Mount -...

Physically screw mount a fan onto the anet.

Easy DIY cover for Anet A3 3D printer.

Customized LED Strip for Anet A3 Printer Upgrade

This redesign brings a fresh spin to Brisemuth's ingenious Anet A8 X-belt tensioner idea, elevating its functionality without requiring an additional longer x-belt purchase. The design expertly reaches through the pulley support, providing tension by...

I'm preparing to modify 50 Anet A8 kits so that when my students build their A8 printers, the X axis will have Drylin bearings instead of ball bearings that are problematic. The X axis rods are really hard to get out once installed, so I've decided...

Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: Low Quality 0.15mm Infill: 20% Notes: There are minor overhangs present, making it best to print this item standing up. ...While supports could be used, I've...

The acrylic frame provides an impressive 8mm clearance, ensuring a snug yet secure fit. This robust filament holder can effortlessly handle spools weighing up to 1-2 kg, although I have not personally tested it with the heavier 5 kg option. Update...

I mounted it securely to my Anet A8 using M4.7x12mm screws and nuts. Though the nuts might be overkill, you can probably get away without them like Papinist did with his thin bracket design. I prefer a sturdy setup. I also added holes to the Y-Bed...

You will need: - Screws and nuts from your old Anet A8 filament holder (or superglue). - 8 608 bearings (get the cheapest ones for this, it's not a fidget spinner). - 2 prints of parts 1, 2, and 3, and 4 prints of part 4. Step 1: Print four of...

If your smooth rods have drilled out the holes in the acrylic frame, you can utilize this solution to rectify the issue. First, remove the affected frame parts and clamp them together so that the affected holes are aligned. Enlarge the affected holes...

Due to my limited access to hardware while deployed in the Middle East, I've tried to reuse as much existing hardware from the Anet A8 kit as possible. The extruder mount uses zip ties to secure the extruder motors and the 50mm fan is...

Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.28 Infill: 25% Notes: Print speed 35mm/s with a 1.2mm shell thickness and 1.2mm top / bottom thick closures precisely. ... For the Disc and the Bolt Tool use 100% infill...

... original design. By utilizing the added rigidity provided by the thicker acrylic frame, the spooler can now handle heavier loads with ease. ...The frame's increased stability also reduces the likelihood of damage to the spooling mechanism itself.

I remixed this to adapt it for my Anet A8 Plus to upgrade the horrible stock tensioner that was prone to breaking. I bought a new pulley/bearing set to replace the stock one as well at the same time so I sized this to fit that. Link to the pulleys I...

This is a convenient Fanmount designed specifically for use with the Anet Mainboard. Its ease of removal makes it simple to access the main board when any work needs to be done on it. ... The fan holder can easily be installed and removed whenever you...

Modified Design of Fan Cover for Anet A3 Mk II Electric Box This is a modified version of the original fan cover designed specifically for the Anet A3 Mk II 3D printer. The creator of this design aimed to improve upon the existing model, making it...

Since the hole spacing on the P3Steel and Anet for mounting bearings and y-belt differs, I've added mounting holes and cutouts for the original P3Steel parts. All holes are designed as clearance holes to ensure a smooth installation process. Update...

Key Features: * Modular design allows for easy customization * Sleek 8mm acrylic frame provides a premium look * Compact size saves valuable workspace * Easy to assemble and disassemble Materials Needed: * 8mm acrylic sheet ( approx. 1/4" thick) *...

This is a simple x-belt tensioner for the Anet A8 printer. I wanted a x-belt tensioner that fulfils following criteria: G2 geared tooth pulley should fit (the last tensioner I used was too small to accommodate the geared pulleys) pulley should be...