anet a8 hotend 3d models

The bed heater's relocation under the aluminum bed lowered its height, preventing X-axis collision with upper base and hotend contact with the bed. Various other fixes have been uploaded since the last update, including the elimination of springs for...

Super airflow and no cooling issues with the hotend. If you're using an x-carriage for Re-D-Bot and want to use the new fan holder with Volcano, I recommend increasing the holes (you can find an image below) or using the updated version...

A great benefit beside better part cooling is a better view to the hotend nozzle. So I designed this LED mount specifically for HERO ME 5015 dual fan duct, it's easy attachable to the link bar between dual fans. 2020/05/05 Update LED mount for Hero...

You must define one hotend and one thermister, but not two. The best Bowden adapters allow a 4mm PTFE tube to run all the way through them. Chamfer the inside edges of the PTFE tube to minimize blockages. Run the PTFE tube all the way to the plastic...

These efforts include an alternative hotend housing, no more quick fittings to tear up tubing or failed grippers. I am Tommy Dee on the forum. Please register with print3dforum.com to see posted images. If you do wish to work with this solution,...

Fan duct upgrade - better cooling, 5015 fan.https://www.prusaprinters.org/prints/52553-prusa-mini-rhd-front-fan-duct - remix too.Support could be removed by small pliers.FastenersSocket head capM3x45 - 2pcsM3x40 - 1pcsM3x25 - 3pcsM3 nut - 3pcsM3x12 -...

Then guide the Cable nicely to the Hotend :) :) Preparing the Hardware: File the Head of the Nail to be almost half Cut it to a length of 50mm Thread the cable end sleeves to a helping wire and solider it onto the end of the spring Attach the lever...

Check head size of your M2 screws or change holes size. For main part: - threads of original heatsink: M3x12 with nut optionally two screws with nuts, more info below - thread of original hotend housing (looking frontside left one): M3x9 for...

To install the LED holder, you have to unscrew the hot end and the BLTouch to get it over the hotend mount. The screw holes on the LED holder are lined up with the screw holes of the BLTouch, so you just have to screw back the BLTouch with the...

This is a mount for the Bondtech LGX and Phaetus/TriangleLab Dragon hotend, for the Seckit SK-Tank with the carbon fiber X gantry. It includes support for dual 5015 blowers for part cooling, and mount points for a Z probe. I've included a mount for...

Along the top side of the hotend fan mount is an over hang to hide the fan wires. Be sure to route the wires prior to completely installing the fan. As far as the temp sensor and heat element wires I clocked the heat block so the wires can run up the...

... I want to have the top on even when printing pla/petg so made these spacers. They are made to vent out some hot air to not mess up pla prints. I have a high temp cr-5 pro h machine. This is a simple print. Read text on hotend kit on how i printed.

The purchased components include: - A J-Head Hotend for short distances at $4.50 - An ATMEGA2560 board at $5.95 - A Ramps 1.4 shield at $4.28 - Four DRV8825 Stepper Motor Drivers at $6.20 - An Optical Endstop Switch For RAMPS 1.4 at $0.68 - Two...

You printer may vary using the same material depending on hotend and fan configuration. I also use the HeroMe Gen5 with dual radial fans and never cool at more than 70%. For greatest level of strength and reliability, I orient these clips on their...

The mount is installed on the standard mounting screws, but on the reverse side of the hotend. From the side of the wheels. The wheels don't hurt, don't worry about it. You will need shorter screws, used those that remained after installing DDX. ...

Note that The Hero Me system is backward and forward compatible for printer model gantry adapters, fans, ABLs, hotends and some direct drives. To get the most up to date version of the Hero Me part cooling system please click here for Generation...

I employed a crossflow fan that blows across the top of the printer.I highly recommend printing the part from PETg or a more heat-resistant material, as PLA will soften excessively from exposure to the motor and hotend.You can obtain the pressure arm...

I believe the housing for the Hotend fan can be fitted with a nocturna unit, but since i do not use them, it was just guesswork on fitment. The Fan Mounts are punched for using the 2.5mm brass inserts or a 3mm screw. The model was put though...

Due to the placement of the hotend and the two M6 bearings I had to change the Ultimaker firmware slightly to adjust the Max X and Y. X_MAX_POS 212 Y_MAX_POS 214 UPDATE 10-18-2015 - CAD files uploaded as requested by a few people. Please let me...

PLA or any other material is just fine since it doesn't get anywhere near the hotend. There is a small support bridge that needs to be clipped off, but that should be the only support required. No hardware is required. Just hang the clip on the...

The Prusa i3's original design lacked a suitable single-hotend mount. To rectify this, I designed a Ubis hot end mount for my self-sourced Prusa i3, which works with 1.75mm filament. The Ubis hot end has a groove that is compatible with J-head...

Super airflow and no hotend cooling issues. If you're using an x-carriage for Re-D-Bot, and you want to use the new fan holder with the volcano, I recommend increasing holes (you can find the image below) or using the updated version...

Here's a breakdown of the content: **Upgrades** * Helix Drive system * Titan extruder Holder * Another version of Titan extruder mount system * BLTouch holder for Titan extruder * BLTouch Holder for standard hotend holder * Power supply holder for...

Specifically made to fit the e3d-lite6 hotend and a 40x40mm fan, the cabling of the hot end should go around the carriage; if you guide it towards the back side of the printer, it shouldn't get in the way of any parts. I recommend using some tape (I...

Parts requirements -7x 6mm M3 screws -4x 8mm M3 screws -4x 20mm M3 screws (0 for 4010 mount) -8x M3 nuts (4 for 4010 mount) -8x 8mm 2.8mm screws (come with stock BIQU B1's hotend) for 4010 mount How to install -mount the support to the H2 extruder...

The extruder body also has mounting provisions for the Makergear hotend. A Zip file containing Solidworks 2011 source files is available for download. If you have a Gregfrost extruder, you can reuse all parts except the body, idler arm, and...

DONT WORK WELL ENOUGH AT 250MM/S WITH STANDARD PLA Parts used: duet3d IR probe (stock probe compatible) Rapido uhf (doesnt support normal hf) 3010 24v hotend fan from pengda 5015 24v sunon part cooling fans (they are pwm controlled, dont know if...

I chose to put the connect the bed at a lower point by creating an extended LMK12LUU mount, but you can change it depending on the depth of the hotend. I use a Duet Ethernet board and changed the Z-Axis movement from a double Z-axis on one driver...

I desired a radial fan setup that could be easily disconnected and mounted directly to the hotend carriage, which wasn't possible with existing designs. This is still a work in progress as I continue to refine the design based on precise...

I needed for my guides to attach to the top of the printer where the display was originally attached, and for it to feed from a point high enough not to interfere with sharp angles on the X axis when the hotends were near the top of the Z axis. I...