anycubic i3 mega simplify3d settings

So, leave these both set to 1.0. It is left here because it may be useful for adding washout to the propeller. PitchAdjHub: Pitch adjustment factor at the hub end. PitchAdjTip: Pitch adjustment factor at the tip end. **More Blade and Hub...

It was created using openSCAD for HO scale, but it should work well in other scales too, depending on the printer settings. The basic dock variables are straightforward: length, width, and height. You can also change the scale being used to match...

(Cards are laminated card stock)clip_Skills-Scores: Skill Scores backing piece slots into this angled clip.clip_Spells-Scores: Spell Score backing piece slots into this angled clip.Backings:backing_Ability-Scores: Angled backing that slots into the...

I have a set of each, and pick which one I want to use for a given game. Hex Tiles Print 19 of these. Do NOT generate supports. The supports you need are included as part of the piece; break them off...

Re-meshing available upon request, eg adaptive mesh for lower poly count (this is the default setting and is as supplied), uniform mesh for easier editing, strict quads, tris, mixed, poly increase or decrease, etc. No charge to existing customers of...

You can add a spot of glue as you assemble the case to help keep things together – just be sure to use a glue that isn't quick-set and allows time for you to finish the assembly. Print with your favourite thermoplastic |...

Again, use pictures for reference. Take the set aside last A corner piece, either glue/weld the B corners without guidance to the surfaces and hope to get the angle good enough. Or hang the lamp, put the long pegs of the B corners through the...

They can be smooth, textured or set with stones. In India, glass ornaments are common. Made from ordinary glass that is about 3 to 6 millimeters in width, they are worn in groups so that arm movement causes them to make a gracious sound rather like...

The bed and cab’s height are set, this ensures to give your Bog406 a mean looking stance at ride height. Gone is that unrealistic monster truck-like high CG stance. Be sure to use portal axles for the most realistic look! These “Rock Shield” body...

IMPORTANT: The bubble plate is the only part that is not intended to be printed in vase mode, this needs to be printed in normal mode using whatever setting you trust in. ------------ SKIMMER'S CUP -------------- The cup is designed so it just...

Corner Storage Shelves These offer a way to store items in corners between sets of straight shelves. Include at least one 'Corner Foot' in the back edge of corner storage shelves to increase strength. These are simple 5 mm tall by 10 mm wide...

It's your standard, everyday tic-tac-toe!PrintingRecommended settings:Nozzle: 0.4 mmLayer Height: 0.2 mmInfill: 10%Vertical Shells: 3Top/Bottom Layers: 5Supports: NoFor standard gameplay, each player will need three large markers, three medium...

... glue touch the screen. Once set, the setup is complete, and the screen should sit happily on your controller with a nice shade to keep the sun off it. ... I've uploaded the Sketchup file in case you want to make any adjustments to the design.

Limitations were set so that it be printable without support and, of course, fit on your standard chess board. The benefit of the chess piece challenge is that the chess pieces on average only took 20-40 minutes to print. Students could quickly see...

Setting up video stream After spending quite some time looking for a reliable way of streaming video from the camera, I came up with the shell script video.sh included into attached video.zip file. The script requires Raspbian, FFmpeg, libx264, and...

Now, with a pencil - along the upper (!) bars - set short marking lines for two glue dots each. Remove the upper bars again ... apply small drops of super glue to the bottom of the base at each of the markings. The lower bars do not need to be glued,...

Calibrated esteps, secure bowden tube and tuned z off set because this thingy is made of PETG and has the tightest of err, tolerances. You may be convinced it doesn't fit together but I assure you it does indeedy. The fit of the parts may loosen...

washer M4 x 9mm x 0.8mm * 1 set cover plates (see PDF or DWG) * 2 holes 4.5mm on left rear frame, as per attached drawing. For the filament guide: * 1 filamentfuehrung.stl * 1 rod approximately 8-9mm diameter and L=308mm long. * 2 cap screws...

Each half of the frame takes around 8-10 hours to print using settings like .32 layer height, 4% infill, and 4 walls at 70mm/s. For the rest of the parts, I used a lower layer height, about 15% infill, and only 3 walls. Print the frame upright with...

... tie a knot in the cord if it's thick enough. Wire positive to switch, the switch to positive on D1 mini. ALl negatives from LED strips, D1 and power supply wired together. Data line from GPIO 4 to LEDs data.Watch youtube video on setting up Wled  -

A remix of the already excellent Screw measuring tool, M2-M10, 4-120mm by Boogie, itself a remix of Quickly Measure & Sort M2, M3, M4, & M5 Metric Screws up to 50mm Long by Sneaks, with some inspiration from FlashTech's “Screw measuring tool,...

Please make sure you've set up your client correctly and if nothing works, go to the GitHub Issues page, and create a new issue.- X or Y is not working as intended, what do I do? ...Go to the GitHub Issues page, and create a new...

https://www.thingiverse.com/thing:4686693Features:manual set the Laser power or use PWM control, check laser temp and off parallel in-out on DS 15 connectors (in from CNC controlboard, out to aux)Input to use only PWM signal from DS15 pins 2...

Depending on your controller and how you wired the potentiometer, it can be set up to return fully in either direction or center. If you're into a "clicky" wheel, superglue a piece of clear plastic packaging (you know, the kind electronics come...

I was set to do this and then had a change of heart. Inside each bracket is a small 'lip' meant to keep the bracket from just sliding down the riser, essentially fixing it in place atop the 2x2. This lip in essence must be able to hold the brunt...

The recommended one is the one on the left, but if you have the media mod for example, the screw on the right might be better. UPDATE (28/8/2022):Created a Dual Mount version by request of u/The_Chosen_One914. UPDATE (2/9/2022):Fixed a...

Obviously as outlined in viniciusro's summary you can use the "move the carriage" to a spot and set zero from there. The laser aligner is specifically designed for this method with a right angle cut out to align to an items corner. Z-offsets you...

Unfortunately thingiverse will not let me add it propperly. And you may notice at the pics that I set to pillarparts on top of each other. to connect them I printed 4 of those insets from <a...

They are just the standard ones from any arduino beginners set. Quick, cheap and easy.<br>All you really gotta do is feed power into the PWM controller and then cable the PWM controller to the first fan. The arctic P12 PWM have a splitter that allows...

These expert modelers continuously look to innovate within this niche while staying true to the aesthetic standards set by esteemed designers. So whenever clients approach them with custom or unique boat ideas they wish to visualize, trust that...