anycubic i3 mega z axis adjustment 3d models

The design is based on the 3d chess from the old series (TOS) of Star Trek:I made some adjustments to take advantage of 3D printing and I improved the design to my liking. The size is a bit smaller than the original one, since I wanted to print the...

There are a number of parameters that can be adjusted to change the model to suit your needs.TileHolder-HomeAnomaly_v2 - Split tile holder into two (Systems (Blue) / Hyperlanes and Home Systems/Anomalies)TileHolder-SystemsHyperlanes_v2 - Other tile...

For those moments there are gadgets such as snoots, which cut the light and concentrate it at a specific point, but with the problem that they are not adjustable, in addition to the fact that the cut of light they generate is not smooth at all and...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

 If you make the screw adjustment above, printing the adapter out of PETG is workable but I'd have an extra around just in case.  My hotends have been in service since March 2021 with the old adapters and I've changed nozzles a handful of...

Clamp Stop - this is a simple way to stop breaking tiny drill bits because of the original height adjustment knob coming loose or letting the head fall without warning. This clamp will contact the large side area of the adjustable head, and clears...

If you can't adjust the controls so that they became linear again and allow the smooth controlling of the aircraft at all rotation angles of the yoke, it's advised to reverse the modification. You can also replace the original controller board...

These units feature remote control operation that allows users to rotated the light 370 degrees with a hard stop and to adjust vertical tilt through 140 degrees. Remote operation is provided by one handheld wireless remote controller that operates...

I updated the plier segment, adding screwdriver files, which provide flexibility when assembling together by different users according to type needed at specific moments (like adjusting band size too). It also comes with three pivoting parts so...

I have started with the Official Metric Remix, which is mostly adjusted for M4 screws and 12 mm rods, and adjusted as needed.PrintingEverything printed with variable layer height, 0.2 mm base profile, 3 perimeters, minimum 1.2 mm bottom and top...

The harness is made of nylon straps and is held together with adjustment clips so that it can be sized to the user.    The fourth system is the cable mechanism. The cable mechanism consists of a combination of nylon strap and metal cable...

tested and works very well. Motioneyeos does not need a movement sensor (PIR) the camera is always on and frames are compared to each other and when a frame is different, ie something has moved then it starts to record to the SD card, live or...

Please see the screenshots on how to adjust the parameters.If, for some reason, you do not manage to edit the fusion file and export yourself the models, leave a comment with the sizes (Upper-/Lower Diameter, Inner-Diameter, Height, Wall-Strength)...

Adjustments to the box dimensions may require adjustments to the arm. But knowing <b>it can be done</b> should help you succeed. (2) I loved the idea of printing with battery box in place, but for some reason my paperclip half-ass battery box wasn't...

)&nbsp;&nbsp;&nbsp;PROS and CONS about the GAUSS Deck:&nbsp;1.) "0 strain" &nbsp;on the usb C port as docking always happens perfectly aligned and secured!2.) no scuff marks or scratches &nbsp;from sliding motion when&nbsp;docking&nbsp;3.) Modular...

You can adjust it higher as you see fit, but make sure the chuck and jaws can spin without hitting the bellows.A little contact won't hurt anything, but you probably don't want the chuck always brushing the bellows. That will likely begin to fray the...

Slowly adjust this single bolt, if you go to far you will have to push alignment block and belt back in and then pull on belt outside of carriage to get slack back. Move carriage around and re measure, repeat until square. Once all is good tighten...

Thrust vector nozzle, and stator bowl will be printed in TPU for its reliable layer adhesion as these components will have servo wire inserted and removed repeatedly if adjusting ride plate or throw arm connection. STL files are already saved in as...

Or adjust your settings if needed.Use ‘threadlocker.’ Real thread locker is CA based, so I figured I could just put some CA glue in the hole and use it to take up space and add some friction. It worked great! I applied CA, tightened down the pin, let...

(If not Adjust the "ball nut tolerance"parameter in the case openSCAD file and create a new STL file.)Step 4: Wire-up and fit the cameraThe Unifi G3 Instant Camera is normally powered by a 5Volt adapter with a right-angledmale USB-C 2M long...

The 5mm X 127mm hole is a strengthening hole.Version 2 servo bracket has a wider base to make it easier to get the arm screw out.3 piece outrigger uses 100mm x 5mm carbon fiber rods for strengthAssembled with items purchased from Amazon.Arrow Shaft:...

Here are the instructions, and CAD model, DXF, &amp; Print for the adjustment tool to remove and install the clutch for Snapper #6-0601 Smooth Clutch Kit for Riding rear engine riders Mowers.The tool sells for $18 online, save the money and make 1...

The tube should stick 1 mm above the mount please report when the tube length needs adjustment.Print instructions:Print in PETG, ABS, ASA or other high temperature filament. The mount cannot be printed in PLA as it will melt.</p><p>Print both the...

The lamp can be easily adjusted up or down 90 degrees and locked into position by simply loosening the two hand screws located on either side of the light head and retightening them once the desired angle is found.LED Benefits: Unlike gas burning and...

(The screws are adjusted to fit tight. Please don't give up and screw the screws into the bed tightly.)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;When we remove the M3 screws, you will see that the m3 screws thread into the...

so the wall plug should be accessible My selection of parts is not a recommendation either and parts may not all fit easily and may need adjusting This case is 8.2 litres 345 x 212 x 131mm (13.6 x 8.4 5.2 inches) that fits a standard size ITX...

I've also provided the STEP file for the whole set, which won't be a clean to work with, but should make adjusting tolerances much easier.The cases all have passages on the back to allow them to be cleanly zip-tied to a post or something.Planned...

Contents Hard outer shell (made of polypropylene) Flexible inner shell (made by EVA form) Elastic cord Belt clip that adjusts the length of the elastic cord Copyright holder of jamclasp https://www.thingiverse.com/thing:4245317 Jam Clasp for 1/4...

The arms are designed to screw onto the servo horns, though i do not have a set of those horns to test with, so some adjustment and or drilling of a center hole may be required. I simply imported the base STL files for the Chip-e, then extruded a set...

The arms and included mount plates are designed with adjust-ability in mind, so the mounts have a bit of range where they can be attached to the arm for either clearance requirements or personal preference. The included parts are also small enough...