anycubic predator linear rails 3d models

(Screw count and length will follow) ****Note to consider**** In order to use this mount you have to turn the Z-Axis MGN Rail mounts by 180° in order to get the bed frame higher. This is needed as the whole setup is so short that you the normal...

The printed bolt (with optional bolt extension from the inside of a Bic mechanical pencil) is inserted through the end hole and secured using one M3 screw which goes through the rails and printed bolt hole. The screw secures the bolt into the...

Here are some updates: - Increased space between horizontal rails - Added angle tuning plates 0.8, 1.3, 2.1 mm These are designed to be printed with 0.2 mm first layer and 0.16 mm layer height 100% infill. Stackable. Just insert it into the main...

Shortened exhaust air scoop for maximum working range (does not fit all K40 designs) This part works very well to connect the timing belt: https://www.thingiverse.com/thing:4175874 12012020 update: Fastening clips with spacers integrated to laser...

http://a.co/d/b0CpHTO Parts you will need to complete this 196 mm of Estes BT-50 body tube 68 mm of Estes BT-20 body tube Shock cord 12" to 14" Parachute Nose weight (clay or lead pellets) The launch lugs can work on a typical rod or small rail....

that fit on the dovetail mounting rail. Just pop onto the pegboard and insert two M3 screws and then slide the Mount on the holder and enjoy. The mount has pegs 4 inches apart.&nbsp;</p><p>One feature is the small hole on the top that fits 1.75mm...

SummaryEverything should be resin printed except the chassis (which should be PLA).ALSO,,,,, Please note, due to Sketchup not liking very small dimensions, the wheels should be printed at 25%Unless stated, superglueand accelerator should be used and...

You can use the ground and 3V3 rail on the RPi to power it, but you'll need to have an appropriate resistor installed inline.It's running the following software: Raspberry Pi OS, with Desktop (it's slow on the Pi Zero W, but it was extremely helpful...

It created a cloth hook out of two 2D SVG shapes that are extruded into two solid rails, where only the intersecting part ist taken as the hook body. This gives you a wide range to create your own custom hooks. Have a look at the hooks directory in...

A few useful items for extreme macro photography (magnifications 5:1 and up, using microscope objectives, and an automated focusing rail - e.g. the one of my design, Fast Stacker: https://www.thingiverse.com/thing:4946939 ). I provide both Autodesk...

... of the thumb screw to tighten the screw and clamp the joint into position.</p> <p>Place the camera on the platform and pull it tight with a strap-band. Due to the rails around the platform, it should sit there without a chance to move or come loose.

It's interesting that most of the existing lighting solutions are top mounted and would introduce the same problem so I created my own side lighting design.Some design features:The lights mount directly onto the side of printer frame in a similar way...

To mount you will need to remove the two front bed leveling (tramming) nuts and lift up ad slide the arms into the bed rails. This will be somewhat tight to hold the arms tights and force (gently) the bed bolts back through the openings and return...

-Toolless Disassembly -Blowback/Recoil Action -Full Talon Support -Solid Frame And Slide Construction -Less Hardware Needed -Improved Ergonomics -Minor Reduction In Size -Larger Battery Capacity -Tac Rail Option All The Files Are Contained In A Zip...

I also made sticky noteholders and an extremely versatile phone mount, with dual cable management rails, and the outer piece acting as a securing/locking mechanism to hold your phone in place as it charges. As virtual learning is on the rise,...

It seems mine could have used a 1 or 2 % upscale, because its a little tight on the rail, but it still works.....The red dot or hologram will only be seen by the shooter, the person in front should not be able to see the dot (unless the light is too...

Just replace the PTFE support on the hot-end with the hot-end clip, screw the other end into the rear 4020 rail, and clip together enough of the individual links to match the length of the wires. I'm using 29 for a 300x300 bed. Run the wires in a...

The whole setup can mount either inside or outside the rear rails of the printer. I've ran it both ways, but moved it to the rear to avoid any potential snags from my bed wiring.</p> <p>A lot of 3-support mechanisms (or customized 2-support) others...

The reflex sight model is an accessory designed to fit on the top rail; you can either leave it hollow or use the included template piece to cut out a piece of clear plastic to act as a lens. There is also room in the base to accommodate some small...

He helped me a lot in getting more and better information about British road-rail containers, so I can continue the “containerization”-theme at a higher level. Many thanks to him! All models sized for British n-scale (1:148). Conversion values: ...

It's a Portal turret shaped more like an egg that can open like the actual turret in-game! Notes:- Every stl was positioned for the recommended printing orientation. - The 100% egg is 8cm tall (without antennae) and 200% egg 16cm (without antennae).-...

Flies on 3/16 inch launch rail. User will need to supply the following materials: - Set of 3d printed parts One each of three individual tube mounts Two nose cones Two centering rings - Two 29-mm 34 inch length body tubes,...

I also designed a new console mount sine the old one wants to hang off the top of the rail and it let plastic get into the cracks. For those who dont have a bigger printer just print LHS/RHS instead of the full thing. The bed is no longer hard...

Made it 5mm deeper and added a "handle."Got tired of using a single piece of scrap aluminum and wanted 2 identical spacers for leveling the X-axis (formerly, calibrating the Z-axis height, a misnomer) so I came up with these.They're 70mm tall and...

- The "RailStop", which is a stopper for the "rails" inside of the body, to stop the "BitHolder" from being able to slide out. - The "Cap", which consists of two parts, but are meant to be printed in place on or around each other. ... ...

Mi recomendación es que lijes un poquito y vayas probando sin forzar. De todas formas no tendrías que lijar mucho. English: You need to slightly sand the long pegs that go into the aluminum rails so they can go in smoothly or they will be too snug....

Also to cinch the pannels to the rails we will use some M5-8mm bolts (see more here: https://amzn.to/2Wi8yXy ) along with some M5 T-Nuts (see more here: https://amzn.to/2Lg2zMk ) Worth note: you will need a larger 3D printer like a CR-10...

Flies on 3/16 inch launch rail. User will need to supply the following materials: Set of 3d printed parts One each of three individual tube mounts Two nose cones Two centering rings Two 29-mm 34 inch length body tubes,...

This means that each object`s yTrans has already been set so the under desk cabinet is under the desks, the overhead cabinet is above the desk, and the telephone is on top of the desks.Presets:* "L" shaped* "U" shaped* Manager (with 2 visitor...

Step 3 Attach the bed leveling foot to the OpenBeam rail, then place the bed on top of the springs, and screw the bed leveling knob on the top. All Done! ...I recommend using this part for leveling once installed: http://www.thingiverse.com/thing:97151 ...