ask linus tech tips 3d models

Also, each combination has a “right-handed” and a “left-handed” variant: not all books open the same, do they? How to Print - Tips and tricksUse a 0.15mm layer height, with a 0.15mm first layer height (not the usual 0.2). It works well with a...

At this point in creation when perfection already reached and there's no place left to tweak any last details you'd be wise enough knowing when not enough round corners isn't a necessity but having them does give an extra polished look so your three...

In some cases, I had to shave the tips off the pins a little, to get the parts to fit flush against each other.) It may be worthwhile to check out emmett's other snap pin designs, which I did not. - I did not change the dimensions of any of the...

** What's Included In Full Set** --- - 32mm Bases (blank, numbered 1-16) - 32mm Skill Rings (blank, skills, positions, numbers, staff, inducements, stats) - 40mm Bases (blank, numbered 1-16) - 42mm Ball Tokens (flat, beveled, and chamfered) ** What...

There are two smaller pegs which provide an even base to prevent the pi from tipping toward its USB. The lid holds the pi firmly in place on its pegs and minimizes rattling.Minimalistic: Lid is flush with bottom and the case has a clean, understated...

Wrap the tip in dark electrical tape to prevent the light from leaking through.The servo arm's need to be rigid so superglue the arm into position on the 3D print.We need to know where the center position is on the servos so I programmed the servos...

I love to get better at this stuff, and any tips on that help a lot. Print instructionsCategory: Music Print Settings Resolution: 0.2mm Infill: 20%-100%, higher infill=higher strength Notes: Wall count: 3 Supports: Everywhere Print all parts with a...

I made some tweaks to enhance the part and also attached both the .stp file and the .stl file for your remix.I did a few enhancements as detailed below and in the pics:Added a viewing port to see the nozzle during print.modified the right mounting...

Additional tip: you can replicate Scene from Product image #2, as included Studio scene and box will provide everything needed for simple yet precise setup of a tabletop within minutes. No worries regarding use case - this chair fits well in many...

To clip the fan and duct arrangment to the heatsink mount part, tip the duct forward and put the tooth of the clip into the slot at the bottom of the heatsink mount part. Then push the upper part of the clip toward the heatsink till it snaps in...

**Cable tip:** TIEGEM makes an usb-c cable that's 30 cm long and has 2 x 90 degree connectors. This is just about the right length, and the color really ties the whole thing together. Still working on a new clip-on version of this design with a...

nyloc locknuts) Post-Printing Tips:Remember to find and remove all supports from the printTest-fit the bayonet connections (may require a little xacto knife trimming of stubborn support material off the bayonet stubs inside the 3D printed arm...

This seems to be a good guide for painting printed parts: https://pinshape.com/blog/4-easy-tips-for-painting-3d-printed-parts/ My printer is currently out of action with a broken heater and fan issues, so I will upload pictures of a printed and...

As always I will promote and REWARD the first people to post quality makes (must enable tips on your profile for reward). A quality make is a successful, complete, hopefully decent looking print at 50% scale or larger. This doesn't necessarily need...

-Here is my onehanded video on how to remove the drawer XD https://youtu.be/-uW8lKUrjRk ** There are 4 files for some reason there not showing pictures but hoping to get that sorted soon Big thanks for everyone who's tipped me! ...

A token tip would really make my day if you like this. Edit: 25/4/2018 - added a bit of tolerance (0.4 mm) to the screw holes so that they're easier to use. You can change TOLERANCE and SCREW_DIAMETER in the scad file if you want to adjust things. I...

Rounded the tips of the grass blades to make them less likely to warp, small revision to the text. Attached here are the rev 5 files. I've also started playing with some dual extrusion prints of this, so far so good! ... If you find you have further...

We have been able to design, prototype, fit and finalize the product.PRINT INSTRUCTIONS:All printed with Original Prusa i3 MK3S, with 0.4mm nozzleBOTTOM FOOT: Filament: FlexFill98A, Layer Height: 0.3mm, Infill: 40%, Fill Pattern: Adaptive Cubic,...

Use a fine felt tip pen to accent the timing marks on the OD of the rims and the hex pin peak. Press the second rim half onto the hex pin. The center-line gap between halves should be very small. Step drill the axle holes 3.9, 4.0, 4.1 mm and 4.9,...

Or click on the **"tip designer"** button. --- # Buy a Kit or Part --- [Coming Soon] Please visit my Facebook shop to buy kits and parts **[Facebook Shop](https://www.facebook.com/thekdjstudioscom)** --- # Questions? ... --- ...

If you like my work, you can support me through Patreon or a tip through PayPal: https://www.patreon.com/gigapenguin3dprints Description A base for LCD Models Mclaren 600LT, it should fit all other colour variant LCD Models released. I made this...

I hope some of you manage to have some fun with it as well! I only had gray PLA on hand to print the test tiles out; if you'd like to help me get more colors and encourage me to make more tiles for this system, as well as more D&D minis, consider...

I'm open to suggestions and tips ;). If you're a plant specialist, don't hesitate to leave a comment with a suggestion. If it's a good idea i might add it to the design !</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p>...

Remix of https://www.thingiverse.com/thing:5151234, but it wont let me put that in the actual remix link boxNOTE: Update posted with H2 mounting holes 4mm lower to fix clearance issue with the duct tips and the shorter heatbreak in the high temp...

the M2.5 screw needs to be 6mm sticking out when you mount the plastic part at the tip of LM10LUU bearing in order to trigger the endstop...(insert the screw all the way into the plastic part then you cut his head off... you can put a long screw and...

A small yet deadly spear design, characterized by 108 vertices that bring its sharp tip to life. Spear_2…........316 polygon. This larger spear variant boasts an impressive 166 vertices, making it perfect for hunting and combat. Spear_3…........82...

That seems to work, but I need to come up with something. I am open to suggestions. If you like my creations, and want to show me some love or give me a tip, you could always buy me a coffee! Update 15: added separate lid, and gold, faith, low and...

With a small flat screwdriver, push the tip of the "blade +" inside (1 mm or two will be sufficient). Place a second blade under the first one, it will serve as a guide to reduce friction. Push the "+ blade" using your thumb to make it pass the...

If you set the distance closer to approximately 20mm, you'll find that you can tip the levitator on its side and maintain the levitated object in place. This demonstrates that the pressure applied by the antinodes is on both the top and bottom of...

In order to maximize bed usage, our only option is to route it to the left, otherwise by going back the cable it will hit the vertical frame on the right side when probing the far right side of the bed (since you need to move the carriage as far...