attack on titan 3d animation

I designed two halves of a power-supply cover for the DPS5005 and DPS5020 from Ruideng (RIDEN, RD TECH) which fits perfectly with the 200W, 48V switching powersupply from Velika. As powerswitch, I am using an Inlet Combi-Module C14 with a lit...

There is a template that you can print to make a hole for the threaded inserts.place the threaded inserts make sure you don't go through all the way.you also have to make a small slot for the wires (refer the image).open the caliper and solder 2...

...Put tape on the inches vernier middle piece, place the slide in place, and affix the inches vernier top face using the slide as a guide for spacing. The above paragraph probably doesn't make sense, so cut a few extra sets of parts if you can manage.

I added my Prusaslicer 2.2 settings in the file Gatter-T_PETG.3mf.update 29.12.2020Since, depending on the filament and the print bed, there may be problems with the print bed adhesion, I uploaded a fence part without the one-sided hinges. You can...

I've designed up this MKS quick release pedal holder to install it on my Brompton folding bike. I had bough the Ti Workshops holder, but I didn't realise that it goes in the same place as the kickstand I had, so I was forced to come up with a new...

I needed to clean up the inside pocket of the case on two prints. A quick scrape with an X-Acto blade worked perfectly.</p><p>&nbsp;</p><h4>Assembly</h4><p>The video above includes assembly instructions. I suggest watching that before attempting to...

With time running out, the Beast embarks on a journey of self-discovery, seeking to overcome his inner demons and find redemption. As he confronts his past mistakes and learns to let go of his anger, Belle's kindness and love serve as a beacon of...

If you're interested in purchasing other game accessories, I sell them on my Etsy shop at the following link:...

3 - 50 products Office Chairs Full Set - 150 products Cafe and Bar Chairs - 30 products Lounge Chairs Collection - 50 products Cinema and Airport Chairs - 20 products Bean Bags Chairs - 23 products Beauty Salon Chairs Collection - 20 products...

Unfortunately, I haven't managed to create a video yet, but you can check out two awesome videos of the original bob here: https://www.youtube.com/watch?v=EU2a39ZfssQhttps://www.youtube.com/watch?v=uN_MRTIMHz4 Get ready to choose your team, print and...

... helps kids create handmade goods easily and successfully. I hope this will be enjoyed by Scouts, Guides, and other youth organizations!\r\n\r\nPS The largest pattern had an unintended bump on the base of the print, but it has now been corrected.

This board will mount with either the SD/USB on the left or the right side of the box (see pictures). Also added, two new lids with 80mm and dual 80mm fans. 5/2/2020: Added a new bottom section that fits the Raspberry Pi 4B. 4/16/2020: Added a...

... to the drill body. Support blocker was applied around the threads to minimize the possible impact the supports may have on the drill threads. ...Support blocker was also applied around the drill body hole, which does not require supports.</li></ul>

Everything should snap together, but depending on your printer, you might need to add a little glue to make things snug. Print the planet portion in your favorite gold filament withArchimedean Chords as the bottom/top infill to get a beautiful swirly...

&nbsp;FeaturesHas separations to accommodate different lengths.Also it can be mounted on the peg board Or any board.&nbsp;It might look bukly at first..but here are my two other prototypes...In hot summer days they did not last.. it was PLA tho.. ...It...

Mashup_type takes on a specific setting numbered one that's part our initial inputs while six height dimension now accurately set to measure exactly 6.75 units along its horizontal plane according all previous measurements before determining other...

The HyperCube parking extruders allow you to switch between two extruders on the fly, which is super useful for printing complex objects. The design consists of two parking hooks that hold the extruders in place when not in use. When you want to...

...Too little torque on quick retractions. It was like it couldn't get immediately started so poles and small features were terrible. I swapped to a moons 1.8 pancake motor and it works great. - I do use upgraded fans, might be better for forming tips.

This is a modification of the Mantis Dual 5015 toolhead for use on a BLV MGN Cube with the metal kit. It has also been modified to use the Orbiter v2 extruder and Mosquito hotend. The BLTouch(and Biqu Microprobe) offset x=0.00, y=-29.00mm, z=0.00...

On peut ensuite réaliser les opérations suivantes dans l’ordre qui vous convient le mieux: - Emboîter les autres maillons, - Fixer les deux pièces H et I au moteur, - Remplacer la pièce A par la pièce B (Bss ou BS), - passer les câbles proprement -...

By holding it this way, you can use this handle if you have a cast on your hand, or have a thumb amputation. This was designed so a wide range of silverware can fit into the base of the handle. Version 2 was designed to hold thicker silverware. The...

There are holes for another 2 to 4 bolts/nuts on the opposite end too, but I've never mounted mine to anything so I've never used those. Works For Me PLA, 0.4mm nozzle, 0.8mm walls, 0.2mm layers, and 20% triangle infill are what I used for this...

Pause print before first layer covering the hole (the exact height depends on model) and insert the magnets, then continue printing. Remember the correct orientation of the label!</p> <p>The default model (SD card box with lid and rounded corners) is...

⚠This replica was made for a video project and is not, in any way, meant to be prejudicial. I am not responsible for what you do with it.⚠Cette réplique a été faite pour un projet vidéo et n'est, en aucun cas, faites pour porter préjudice. Je ne suis...

**The Goal** I wanted to completely eliminate z-banding/noise caused by stiction in the lineair bearings/bushings on the z-axis guides. I achieved this by improving rigidity in the z-direction with a belt-driven triple leadscrew build platform. You...

The methods the broader community use are relatively imprecise/subjective/semi-quantitative (https://www.thingiverse.com/thing:1662956) because they rely on non-standard illuminants and human vision. These have obviously been adequate for many makers...

... The Barndoor is attached on the side or at the top of the key-light with a "1⁄4 inch wing screw." The hinge can be tightened with thumb nuts. Any material up to 3mm thick can be used as a door (in my version it is a black aluminum composite panel).

Originally published here: Ariel with known topography scaled one in ten million by tato_713 - ThingiverseThis model was rendered using MATLAB R2016a on topographic map from Schenk (2008), made with the images from the Voyager mission. When the...

A nut is glued into it on the opposite site, so even if the handle's bracket part were to break, the rope will still be attached to the camera and you. I assume that once the plexiglas part of the bracket breaks, it's gone anyway. I printed it in...

Based on the blueprint of Boeing's design assistant Assisted by the example set by Boeing's structure, assistant Taking after the plan of Boeing's concept, PENDING assistant Following in the footsteps of Boeing's layout, assistant Drawing...