basf filament 3d models

You will need a little over 3 rolls of 1K filament spools to print this. Have some spare rolls on hand in case you have failed prints. Some of these parts will use over 1/3 of a 1K spool. Some of these files can take over a day to print. On some of...

The specific settings should depend on your printer and the filament used for printing. Placement of models on the printer table when printing is shown in the photo the Cura slicer shows a scaled-down model using the slicer itself. Its files For CNC...

 Since it's best to leave them open for some filaments such as PLA, I wanted them to not be swinging outward where they could be in the way and/or get easily damaged by being run into.This replaces all 4 front corners, the top 2 side middle...

That way the warm air passes through the desiccant and some of the moisture should be extracted before it gets to the filament. I also leave the outermost ring of the tray base attached to the outer wall of the trays as it keeps them a lot more rigid...

The process of adaptation presupposes that practical aspects of printing the model using the DLP/SLA/LCD technology are taken into account, and the model's scale and cutting are chosen to ensure an optimum result of printing.3D PRINTING...

If you like my work then please do not forget to "tip designer" to show your appreciation and to encourage me to publish more designs in the future. Print Settings Rafts: No Supports: No Resolution: 0.2 lampstand 0.1 lithophanes Infill: 25%...

 If you would like a looser fit, or if you find the original files too tight you can use the files with the “-medium” (0.8mm offset) or “-loose” (1.0mm offset) filename suffix .If you're unsure of which one to use, I suggest printing out the...

If you want to show your support, donate to a charity that could really use your help and funds.Have a great 2022.Print SettingsPrinter Brand:CrealityPrinter:Ender 5Rafts:Doesn't MatterSupports:Doesn't MatterResolution:0.2 - 0.3mmInfill:20%Filament:...

Similar tubing can be printed from flexible filaments too. This rounded edge or rim of the mask can be easily adjusted for any required inner diameter of tubing, either by me or anyone with moderate knowledge of Fusion 360 software. All it takes is...

It would be a good idea to print this part at the low end of the temperature range for your filament and at a lower print speed if you have any issues with it. Most of the part is covered/hidden, so any defects will not show anyway. 4 - A number of...

8.If you want to place the filament sensor as close to the extruder as possible, remember to insert a longer cable. 9.install the 4020 layer fan with the 3 M3x18mm screws and attach the vent duct according to the model chosen. if you opt for the...

Otherwise, some suggestions: Antenna - print concentric with brim Head - print concentric with supports Visor - print concentric, face up, with brim Eyes (2) and Teeth - print together ("complete individual objects") Body, upper - print bottom down,...

I will post the updated STL files in the next day or two. 6/5/20 Initial posting of un-debugged STL files. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 1.5mm Infill: 15% Filament: Hatchbox PLA Category:...

If you have the proper filament colors, no painting is needed. The assembled model is 155mm tall. Note: As I research characters that I model, I learn quite a bit of interesting background on the characters. I found a video of how Sonic was...

I printed mine in eSUN PLA+ however most filaments should be suitable. Assembly After printing insert two brass hot inserts into the fan housing and four into the stand. These can be easily pressed in with a soldering iron, if you want them to be...

I recommend that once you have the position decided and fitted that you add a dab of superglue between the socket and the clamp to prevent any rotation happening accidentally if the screw loosened or the assembly got knockedAccessories(Colours are...

Getting the blue right was a little trickier, but I found that eSun do a very nice dark blue PLA+ filament that close enough to the official colour used on the London Underground. FINAL THOUGHTS: I hit one small problem with my lamp that...

 See also my sunshade for the FeelWorld 5 ½" Field Monitor at:https://www.printables.com/model/240027-feelworld-fw568-5-12-inch-field-monitor-shadeAs you can see from the last photo, the whole rig (without follow-focus and camera) compresses...

There are spaces for eight magnets, but in practice a pair of 1/8" x 3/8" magnets or four 1/16" x 3/8" magnets per side are more than sufficient.The version the I built uses a 1:48 geared motor, but the 1:90 geared version would be more appropriate...

If you are interested in testing mounts for different sized bottles, please contact me and I will make one to fit your bottle.Print SettingsLine width: 0.4-0.45mmLayer height: 0.20mmWalls/perimeters: 2-3Infill: 20% except Core Type A Center: Infill...

Parts (in addition to filament) * [6off 8x2 magnets - I used 8x2 N42 1kg pull magnets that I already had](https://www.first4magnets.com/circular-disc-rod-c34/8mm-dia-x-2mm-thick-n42-neodymium-magnet-1kg-pull-p3010#ps_0_3056|ps_1_16656) *...

Alternatively, you can attempt to work around the issue by printing the caddy with a 'raft' and/or by increasing the Lip_Gap value.MaterialThis design is perfect for printing in many filaments, including PLA, PETG and ABS.Versions1.0 (20 Jul 2022) -...

I recommend printing with ABS or another filament that will withstand high temperatures - as the bed is indirectly resting on the bed supports, these will get hot. I've printed mine with ABS, and regularly run my bed at 120 degrees C without any...

...Currently deprecated, though it still works. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: Yes Resolution: See below Infill: 10% Filament: Any PLA Notes: Table clip should be printed sideways and does not need supports.

If you have the proper filament colors, no painting is needed. The assembled model is 175mm tall, 315mm long and is mostly in proportion to my previously released Looney Tunes models. Enjoy! Special shoutout to maker Benoît Lussier for providing QA...

I found this one which looks identical with the buck/boost capability. https://www.aliexpress.com/item/32611751890.html?spm=a2g10.10010108.1000016.1.57a9185fztpWs4 Terminal Blocks 2 position 7 each:...

Do NOT attempt to use the normal bed leveling with the dial mounted, it will hit the frame and likely break!Print SettingsPrinter:QIDI Tech X-MaxRafts:NoSupports:YesResolution:0.2 mmInfill:25Filament: Prusament ASA Jet BlackNotes:Print all parts in...

The specific settings should depend on your printer and the filament used for printing. Placement of models on the printer table when printing is shown in the photo the Cura slicer shows a scaled-down model using the slicer itself. Its files For CNC...

The minute arc is designed to have the filament color changed near the end of its print (included in gcode), so the minute figures stand out. The typeface is the excellent <a href="https://fonts.google.com/specimen/Voltaire">Voltaire</a> by Yvonne...

&nbsp;If you have the proper filament colors, no painting is needed.The assembled model is 175mm tall when sitting flat and approx. 240mm tall when the legs are bent.</p><p>Enjoy!</p><p>Special shoutout to maker Benoît Lussier for providing QA...