bcc 3d model

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches to...

twisting both wire pairs reduces possible crosstalk and possible issues from it. there are holes for zipties after each dragchain, use it to secure the wires but leave some wiggle room for the wires inside the dragchain, if they are to tight...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_size = 40 stencil_shape = 4 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

... You'll hear of a good change once more after fixing and updating the walls here: with even those not fully set designs being optimized properly with a little extra bit going onto your current model too, this will look awesome when everything’s set!

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

don't use tin based silicone since it's not high temperature resistant) For this model you need not more than 30ml of silicone in total (15ml A + 15ml B), but if you buy 500ml or 1000ml tare, you'll have a lot of fun creating molds and casting cool...

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to [**domino6713's dice tower courtyard...

... of the Reitec polisher. 24.06.2022 - Updated the Drumgear to be the correct one. Sorry for the confusion. 24.06.2022 - Added alot of exemplarotry images / and Photos and added alot of BOM. 27.06.2022 - added alot of forgotten models. ...Sorry

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

I might model a charger later on to hook up to my regulated power supply. Thoughts Well, in my search for replacement batteries I found so many brands who relabeled these machines... it would be interesting to find the original manufacturer or...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

... tolerances must be around 2 tenths of a mm, it is not essential to use CNC systems. The pieces can be easily made by any turner or by a modeling enthusiast and their cost is quite acceptable. ... Criticisms, suggestions and changes are welcome!

Before you merge them, DUPLICATE the logo "hole" model (Ctrl D) do not use copy paste it will "shift" duplicate will keep it where it is. Now shift select the body and merge to make your hole cut. You will note you still have the duplicate hole. Now...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

Included are the STEP and STL files for all the printed parts along with a Fusion 360 model link: https://a360.co/2QkvXpV **I feel it important to acknowledge Roberto Gil (jgbbob8) for his contribution to this project. When in late 2017, I added the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

I recently built some model catapults, and I realize they just use a peg to hold arms into place. So I borrowed that idea, using two interlocking pieces. One piece (looking kind of like a ladder) inserts into slots, and pegs from the top hold the...