border collie 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

... Very basic stress testing was done in Fusion360 with a model of a 1.5" PVC pipe sleeved over the mount and it seems like it won't snap too easily. ...In real life testing, it holds a ~7lb antenna easily.</p> </p></div></p></p></p> Category: DIY

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

I created this VW Passat B8 phone tray because my iPhone 8 with cover didn't fit into the standard one. Rotating the USB port by 90° it has space for phones with a length of up to about 15 cm which is about 11mm more than the standard tray offers....

This model is extremely water-resistant, highly buoyant, and accelerates quickly with my setup. I printed this on my Ender 3 using split parts for easier printing or a single part if your printer can handle the height. The hatch measures 26mm deep,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

Description ==================== The display is mostly based on Modeller's 1/64 Initial D display box but I have expanded and slightly upscale the width of the roads to fit Hot Wheels better. The holes for tying the cars are designed to fit most...

useful as an object holder (Elettronics component, Dyn, various tools, modellism, cutting and sewing, make-up set, manicure, fishing ... etc https://youtu.be/w3FsHNZxC64 Description The chest of drawers is made up of five containers with single...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

The COMPLETE Thieves Guild bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Thieves Guild AdeptsVery little is known about the legendary Thieves' Guild in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

Find it according to your vacuum cleaner model. In the file, you can also adjust all necessary parameters, including the angle for the vacuum cleaner adapter. Copy these values into the snipper file as well, since the first section's angle is needed...

Tree Supports and possibly Outer Brim required for some STLs NOTE: The STL Models may display some artifacts from revision builds, but will not appear in Print RECOMMEND: Allow pieces to cool to room temperature on printers Heatbed before removing to...

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

The assembly is tailored for the older model C8, CeleStar Deluxe with the double fork equatorial mount and an under-rail for weights, dating back to c1998. Materials List • The three C8 Camera Mount Assembly prints o C8 Front Bracket o ...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...