ccm models

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

Note: Scaling down the model too small may not work on all printers. The smaller the part, the more precise your printer should be. 1/2 scale should work well without extra precision. Any smaller will need a printer which supports a step of .05 mm...

I used hinges from model aircraft stores as they were the perfect size. The battery holder can accommodate a Turnigy Nano Tech 3s 2.5amp battery and fits over the support bars on the bottom of the box. Trailer Under runners and boxes: The runners...

I also made some design changes to this model. First, because of the ninjaflex's floppiness, I was worried that the semiflex would not be much better, so I included a small piece that could fit into the charging port of the phone, the goal being...

I printed the nuts and locks in a bright colour to highlight their function and make them easy to find if they were to fall off. I have uploaded a 3mf file containing all the parts in the correct orientation on the build plate, however you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 0 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Check out the rest of furniture models from it, as they will fit nicely with this mini set! Bar pieces have special connections that allow you to attach them to each other in an unlimited amount of ways, and create any shape of bar that you desire,...

ive added it now an also a squished model of the corner with the strain relief as a test so u can make sure its going to fit around properly. this will more than likely be down to how well you have you printer calibrated but ive printed it off...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

The model is made to spec (as if being fabbed with metal or a real 3D printer) so it's up to you to make it work for your machine. Remember, if using ABS (like I am) to scale by 2-3%. Edit: Improved Method: Order an extra bearing. Take a Dremel and...

I then saw it mention by a Popular Modeller on his Youtube channel and then over the next year the number of downloads went up enormously. So it seems like its time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

Before assembling, rub the moving parts and check the tightness of the fit. To put the button in place, you need to press the back side with force on the ledge on the spring. ##### If you don't have a 3D Printer, you can print it from a Service like...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out of my MHQ...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Even if my model provides screw holes and additional holes to fit the screwdriver through, I don't recommend using them. The pillars the screws were originally drilled in are most likely already split at the top due to the weak plastic. You don't...

Constant testing and printing are underway with mods on nearly every model, wasting over 300 feet of filament in the process. I'd appreciate support for my project as it's not intended for non-3D users but rather for those who want to quickly build a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Since my first published keybboard was The1987 (https://www.printables.com/model/299777-the1987-a-modular-retro-inspired-87-key-mechanical) and it's fairly popular, and its designed around the Phantom circuit board and Teensy 2.0, which are no longer...

... Use your best judgement if you have more experience at printing. This is my first upload, I am still struggling with FreeCad. Hence, the models might not be the greatest so please be kind. Use at your own risk but they work on my printer! ...

Then, I saw it mentioned by a popular modeller on his YouTube channel, and over the next year, the number of downloads went up enormously. So, it seems like it's time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_extra_port_y_position = 30 custom_back_camera_x_position =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...