creality ender 3 v2 filament 3d models

************************************************** Tested on my Ender 3 v2, but should work on other Ender models if they use the same t-slot rail design. The extruder part may need to be connected via a different method if on a model that is...

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

Filament spool holder for ender 3 v2, but I think it would work on other printers too. Note: I had the bolts, nuts, washers, and bearings lying around. The bearing I used were 'bad' (for their previous purpose in a table saw motor) but they are...

Created a larger filament drip tray. Got tired of all the pieces falling in the aluminum extrusion gaps. Grab by the tip easy disposal. No supports needed! Clears most printed fan covers. Print vertically. ...

Useful in case you don't want to use the delivered spool holder (where the filament sensor is to be mounted). ...For best results rotate to its side before printing.

By integrating a filament guide extension, I've managed to merge the functionality of a Z bearing holder and filament guide into a single component. ...I'm pleased with how this solution is working out for me - you might want to give it a try as well!

... time was only 7 minutes, making it a quick and efficient process. Since I chose to use PLA for this project, I'm pleased with its performance - it rolls freely around the lead screw with minimal friction on both the filament and the screw itself.

If you don't use the built-in spool holder, this bracket allows you to mount the filament runout sensor to the gantry.It uses the same screw-holes as the bracket that comes with the printer.Easy print - no supports necessary!

I love the original filament guide this is based on, but when I added a dual Z-Axis kit, I couldn't use it anymore. ... So, I created this remix that mounts the arm on the front side of the 2020 extrusion and still places the guide loop in nearly the...

BOM: - 2x bearing 6906 (30x47x9mm) or 61906 (30x47x9mm) - 4x M4 nut - 4x M4x8 hexagon socket set screw with cone point Printing: - blockade_2 and blockade_2_nut: print with supports (everywhere) - spacer_1 is optional - clean "cover" after printing,...

I wanted the filament spool to be 90 Degree turned to the left side of the printer. So i designed this conversion kit and redesigned the Spool Holder itself. With the redesign you can print everything at once WITHOUT USING SUPPORTS! Just place the...

So the original file was everything I needed it to be: an extruder piece that constrains the filament path more than the stock one, and uses one of the nine spare PC4-M10 couplings I had left over from the 10 pack I bought to replace the one that...

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

Printed and tested on an Ender 3 using Simplify3D without any problems at all - it works great! Note: This is just one part of a set; you'll still need the other two pieces from the link above to complete the design. Note 2: I used 0.4mm for...

So that includes: - Creality Ender 3 - Creality Ender 3 Pro - Creality Ender 3 V2 - Creality CR-10 ### 3 SIZES There are 3 sizes to choose from: - **M** - Medium - **L** - Long - **XL** - Extra Long I personally use the **Long** version, which gives...

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot

This is a remix of the gantry from the Hero Me Gen6 Master Suite for mounting a BFPTouch to an Ender 3 V2 with the Creality Spider hotend. Hero Me 6 - https://www.thingiverse.com/thing:3182917 BFPTouch - https://www.thingiverse.com/thing:2890290...

... just over the know without the need of removing the spoolholder. ... Remixed from: https://www.thingiverse.com/thing:3975794 Using for the paper spools of "Real Filament" as the paper has a bit more friction. ...Makes prints with paper spools smoother.

I have designed a spool holder for the Creality ender 3 V2 printer. The design uses no ball bearings and fits into the stock spool holder. The main advantage of this design is that despite the fact that it does not use ball bearings, the unwinding is...

This Mount make it possible to mount the Display of the Creality Ender 3 V2 directly on the side.The Slots for the Display are taken from this Model: https://www.thingiverse.com/thing:4744628The side to keep hold on any 40x40 extrusion is taken from...

you can replace this with the cap of the original spool and have a double spool as well, its width is 3 cm so any filament can fit

(see in the remix tab) Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.3 Infill: 20% Filament: Das Filament PETG transparent Notes: The part is, as mentioned, optimized for a 0.6mm nozzle for faster...

Orbiter v1.1 and v1.5 adapter for Creality Ender V2. [Join our Facebook support group!](https://www.facebook.com/groups/705637896767655) Updates: 11.02.2021: Uploaded adapter for Orbiter v1.5. 15.02.2021: Uploaded new adapter version for...

A Rough model for the Ender 3-V2 Screen. ...Holes, PCB, screen, and rotary encoders are perfectly aligned.3 September 2022 // Updated the cable port, buzzer, and SD card slot (Rough sketch)

... in one of the photos. My switch dimensions were:12.8mm long, 5.8mm thick, 7.15mm switch collapsed. When soldering switch to connector, be sure to have your orientation worked out.The bearing guide cover was used from another bearing filament guide.

To create a filament runout sensor, use a holder for a limit switch. Cut the middle pin of the switch and then solder pins 1 and 3 to a cable. ...Finally, connect the cable to your printer, as shown in the last picture.You may need a longer M3 screw to...

This filament guide holds the filament out from the printer 100mm and pushes it back about 50mm

Le Raspberry Pi 3b+ se fixe à l'aide de 4 petites vis (Type ordinateur portable) et le boitier se fixe sur le châssis de la Creality Ender 3 V2 avec 5 vis M4 et écrous en T. ... Quelques liens : - Raspberry Pi 3b+ :...

This is a remixed design for an Palette 2 Extruder Clip for the Creality Ender 3 V2 based on the initial design from Tproffen. It is simply mounted with the existing screws - No further changes required. There are two parts which should fit...

redesign of my first filament guide with a longer filament slot to hopefully help with the filament catching or getting stuck if it is kinked or twisted on the roll, plus it looks cooler then the first.