creality ender 3 v2 filament 3d models

Update: This design is superceded by my single-roller design over here: https://www.thingiverse.com/thing:5330621 This is an alternate top filament guide for this thingy: https://www.thingiverse.com/thing:3428924/files . You will need two spacers and...

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this.Just over an hour to print and...

This is a simple filament guide I made because I did not like that the filament would rub against the Z-Axis Guide Rod when printing. To mount, all you do is remove the 2 screws beside the guide rod and slide the piece over. Once done, reinstall...

...Supports are recommended/necessary in my opinion. Great filament guide if you have a side spool holder. ...Don't forget to print the 2 spacers and sleeve for the 608 bearing this mount uses, those pieces are found on the original post I remixed from!

Double roller filament guide which works well with seperate desktop spool holders (or other seperate spool holders).You`ll need:1x bracket2x wheels4x spacers, Additionally:2x 608 roller bearings2x 16mm (minimum) M3 bolts with hex nuts.NOTE: Bracket...

A piece is added to be able to use the tool more comfortably.It allows us to hold the extruder so that we can change the filament more easily and with more care.Two pieces are printed at a time and then glued together.

This is a simple remix to reduce how far out the filament guide extends away from the printer so that it can fit in a standard tent enclosure. ... The big thing though is that it has an updated plug which is a much more snug fit and won't fall out as...

Remixed for better support on the printer so that the clip doesn't keep falling down from the pressure of the filament as it is fed through during printing. ...I use a little piece of tape to hold the extended block to the printer upright and it works...

... (e.g. ... ZZ 6201) - 15x35x11 (e.g. ZZ 6202) or tapered bearing (e.g. 30202) but in my opinion simple ball bearing is enough 2 x M5 hammer head screw + nut or hammer nut + screw The dedicated filament guide should be used for the set (next project)

I personally haven't tested the thin version, but i think it should be plenty strong enough to hold the filament roll. The thick one is shown in the pictures To install, just line up and push it in. It uses the rails to align/hold it in place. I...

Based on idea from: https://www.thingiverse.com/thing:2885049 Remixed between this https://www.thingiverse.com/thing:2873157 and this https://www.thingiverse.com/thing:2147179 I currently use Filament sensor simplified, please refer to this video for...

I wanted a filament guide with a roller, and didn't see one I really liked. Maybe my searching skills need work. I think the print settings on this are pretty forgiving. I printed it with a 0.6mm nozzle and 0.28mm layer heights, just because that is...

The inner 4 M3 holes are for a standard MGN12H carriage and the other 4 M3 holes spaced slightly wider apart are for the MGW12H carriage. There is a very rough video below of it in action along with my X Axis Rail mod. Materials: 1 x 300mm long...

This is designed to be as similar as possible to the stock filament holder, but uses bearings to fix issues with spool gripping on the shaft. Uses two 1/2 (ID) x 1 1/8 (OD) x 5/16 (W) ball bearings (I used...

I recently buy the micro switches from amazon and created a switch holder act like a filament runout sensor. I also added the technical drawings of the switch which I am using. If you want you can use the design without the bowden tubes as well but I...

I recently buy the micro switches from amazon and created a switch holder act like a filament runout sensor. I also added the technical drawings of the switch which I am using. If you want you can use the design without the bowden tubes as well but I...

I created my own sensor that just slides on using the reality 3D printer filament detector found on Amazon below. it uses M3 size nuts and bolts and 688 2RS bearings. you can find the bearing inserts and the outer wheels elsewhere on Thingiverse. I...

I recently buy the micro switches from amazon and created a switch holder act like a filament runout sensor. I also added the technical drawings of the switch which I am using. If you want you can use the design without the bowden tubes as well but I...

Thanks! https://paypal.me/cdsmakestuff Creality Ender 3 / Pro / V2 (?) --- I can only assume this could work for the V2... don't have one to test with.<br/> Part Cooling / Hotend Cooling - Upgrade "Kit"</p> <p>Very lightweight<br/> --- Original...

I created a bracket to allow for permanent mounting of my Creality Laser module to my Ender 3 v2 which also has the CR Touch Auto Bed Leveling Module installed. The Laser bracket option provided by Creality didn't provide an option for a permanent...

I found a nice ender 3 V2 Drawer for the Raspberry Pi (https://www.thingiverse.com/thing:5216947) from OvergrownOrange (https://www.thingiverse.com/overgrownorange/designs) and wanted to remix it to fit my T95 Mini. ... There is a really good tutorial...

I found a nice ender 3 V2 Drawer for the Raspberry Pi (https://www.thingiverse.com/thing:5216947) from OvergrownOrange (https://www.thingiverse.com/overgrownorange/designs) and wanted to remix it to fit my T95 Mini. ... There is a really good tutorial...

... will work with the Crealtiy Ender 3 series. ... I printed the base, two long arms, one short arm and the webcam holder which turned out to be a nice height for my Ender 3 v2 Neo. ... You'll need 4 x 25mm x 3mm (or 4mm) screws with nuts and washers.

This design was intended to be plug&play with the stock extruder on my Ender 3 v2. Part of my goal was to not have to disassemble anything. In particular, I did not want to take the extruder apart as it prints perfectly right now. You do need to...

A display holder for the left side of the Ender 3 V2. You just have to put the ribbon cable on the other side and then you can use the holder. Put the display in the holder first and then scrrew it in because of the Z-Stop. ...(I optimezed the file a...

Compatibility: Ender 3 V2 Neo, possibly fits also other Neo models. Advantages: 1. Air flow is directed better at the heatsink. 3. Heat is disperced quicker and not trapped by the original cover. 3. Weight reduction because the original cover is...

The front models have a ridge that makes room for the screws on the printer, while the rear models take advantage of the all the surface area to stay in contact with the printer!Logo models have the Ender 3 dragon logo cut into the cuffs that hold...

---------------------------------------- This is the second version of a linear rail mod for the Creality Ender 3 and the one I am using now. This mod was done to improve the belt path alignment and create a sturdier platform. With this mod, I...

this is a remix from mattwalls ender 3 tool holder. I made it easier to print the Creality logo in a different color and changing tool configurations and sports. I took out the scraper because i use a much better one thats too big, but i included a...

* Remixed fan duct to better fit the mainboard and adapter plate ### Added parts * Adapter plate that fits mounting posts for the SKR V1.3 and has posts to mount any Creality mainboard. Mainboard position is shifted to move stepper drivers under the...