creality ender3 v2 3d models

A little extra support going perfectly under/over CR10 V2 cover of extruder. This part requires 2 supports that need to be added right away. You also have the option not to use any supports and instead opt for a Nylon Plastic Zip, which can help...

The 3rd-party aluminium extruder for my Ender 3 v2 doesn't have the cable clip that the original plastic extruder came with. This part adds it back. Installation simply requires undoing a corner screw and inserting the clip. Some minor cleanup was...

_2021-04-17_ - I added a v2 of the pinless mount that now clips onto the Z axle after learning that the mount may be coming loose for some users. ... I also updated the Pulley model to be rounder on the inside where the filament makes contact with the...

The corners transition smoothly from 45° to 90° to allow for a continuous loop. NEW FILES:LED_STRIP_CORNER_V2-1LED_STRIP_V2-1Thanks to PurpleR0b0t for the suggestion. /////ATTENTIONMake sure the bolts aren't too long. They shouldn't go past the...

The V2 is much stronger, stiffer and doesn't stick out nearly as far. I found the V1 could vibrate on jerky or quick moves and make a horrible sound. That vibration would probably have some impact on print quality too but I'm not experienced enough...

Dial Indicator Holder used to mount a dial indicator purchased at Harbor Freight onto the head of the extruder on Ender 3 Neo v2 printer. It is shaped on the inside to copy the contour of the head. I installed 2 nylon screws on the top in order to...

... 24V to 5V DC buck converter). * Added companion bottom plate for increased air flow. (Remixed from [Ender 3 V2 Mainboard Cover Reinforced](https://www.thingiverse.com/thing:5174835) by [DreamX_MV](https://www.thingiverse.com/DreamX_MV))

10 screws M5x20 4 M5x40 screws 10 Washers M5 4 Nuts M5 8 Nuts for profiles M5 To be printed: Tree x1 Sup 1-1 x2 Sup 1-2 x2 Low coil blocking x2 Coil blocking high x2 Roller x2 Coil blocking head x2 Washer X2 Optional: Adaptable washer for Creality...

This is a simple, lightweight and modular cooling system designed specifically for Creality 3D printers with Micro Swiss hotends, including CR-10 and Ender models. The system consists of two key components: a base plate that doubles as a hotend...

Direct Drive Mount for Stock CR10 V2 Extruder Prints Very Quickly, Extremely Easy to Use. The extruder faces forward for a clearer view of the drive gear. This makes it easier to work with the extruder and check its performance. There are two...

The front models have a ridge that makes room for the screws on the printer, while the rear models take advantage of the all the surface area to stay in contact with the printer!Logo models have the Ender 3 dragon logo cut into the cuffs that hold...

ITA-ING MUSCLE v2.0 AGGIORNAMENTO BODY: .BODY SENZA LED INTERNI .BODY PER ENDER 3 .BODY PER ENDER 3 V2 AGGIORNAMENTO CON BLThouch, ABL probe, ventola frontale 4020 nella descrizione trovate le specifiche dopo il simbolo >> IMPORTANTE : LEGGERE TUTTE...

This is a new version v2, now with big chamfered edges to make it look more visually appealing. The old one can be found here: https://www.thingiverse.com/thing:3252444. If you found this design extremely helpful or wish to support me in any way,...

This design was intended to be plug&play with the stock extruder on my Ender 3 v2. Part of my goal was to not have to disassemble anything. In particular, I did not want to take the extruder apart as it prints perfectly right now. You do need to...

The aluminium profiles are used from an unknown Crealiy Ender 3 v2 CAD model. I only designed the enclosure itself and the AC plug. Additionally, working with mains voltage is dangerous. You should only do this if you know what you are doing or...

The one by victork91 wouldn't work on my V2 Neo because the front of the top rail is solid. The one by GlobalDisruptor I printed and it was working, but it didn't attach to the top of the rail in any way and that caused it to flex backward and to...

* Hot-end is cooled by a 4010 (stock Ender3) fan instead of the 3010 E3D ships with, though cooling path of the 4010 fan is reduced somewhat in this setup, but appears to be still providing adequate cooling. * I have dropped support for...

E3D hemera mount for linear rails with 20x20mm hole spacing, 5015 radial fan V1_Mounts Was mount was designed for Ender 3/3 PRO with the 3DFUSED X gantry conversion with MGN12H Carriages (but will fit other printers with the same rail system/setup)...

*Before (Creality 42-40 stepper) : 1 3 2 4* *After (BondTech Pancake stepper) : 1 2 3 4* Change the Vref for the extruder stepper ([guide](https://3dprintguides.com/2020/05/how-to-calculate-vref/)) : *0.69 V* for the BondTech Pancake 25mm. ... Change...

[](https://www.buymeacoffee.com/squirrelf) **Please consider donating if you find it useful** (use the "tip designer" or buy me a coffe button) ---...

This is a holder for a drag knife (14mm shaft) to cut paper or vinyl. The tool is mounted with a rubber band to press the knife down. ... Combine with a rubber cutting mat.

92mm fan for ender 3v2 without support. ...Then fan goes outside!

I redesigned the Sensor a little bit to hold in Place without ZipTie or other solutions. I also used the Idea from Sebastiandruckt ( https://www.thingiverse.com/thing:4813860) to reduce the Gap for the Filament to 2.4mm, so it does not Stuck...

Version 2 of spool handle that connect ender 3 spool holder with 52+mm spools. Reduce force needed to rotate filament spool and improve print quality. ... Version 2 improvement - no suports needed - new thread connection - new more universal...

Simple cover to replace the Ender QR code on the X axis.

Y-Axis Upgrade to solve Stepper overheating and slipping, re-uses all fittings. Requires Spare /New 42-40 Stepper and original /new Belt Pulley. If you have this problem, I would recommend: 1. Check belts and pulleys first. 2. You can adjust...

Redesigned the case for a smaller camera set-up. Check the included drawing for dimensions. There is a Angled bracket for raising the camera a bit higher as well. Requires The Following... ... 4-M3X16 Flat Head Screws 4-M3 Nuts

Edited the bracket from RedSodas thing https://www.thingiverse.com/thing:4581110 I have the filament roll down on the table so I needed a bracket for filament to run over the wheel.

<p>I was looking for a possibility to operate my 3D printer power-saving via Octoprint, so that I can also create timelapses and so on.<br>So the device also needs some power to not be overloaded by the image processing.<br>Besides, current Raspberry...

【V-Slot LED Light Bracket】 VスロットにLEDライトをマウントするためのブラケットとなります。 Baseus LEDライト専用サイズとなっています。   【Google Translation】 It is a bracket for mounting the LED light in the V-Slot. It is the size for Baseus LED lights only. ...   【Posted blog】 <a...