custom motherboards form factor idea 3d models

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs sticking up, then rotate to 45 degrees to make it fit on your bed. Print the Front (part)... Then print the Back...

Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held in place with a couple of screws each. ...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

is ASVFSVF14K203 [US] [CA].----------------PrintingThe “ALL.stl” file prints the entire set of models you'd need to assemble ONE power plug housing. Separate STL file for each of the part is also provided for your...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches to...

&nbsp;Obsolete models are deleted and replaced with the latest version. &nbsp;Post feedback so we can improve and keep these collector replicas running!</p><p>Change Notes</p><ul><li>4/5/22, Version 6: Best version yet. &nbsp;Dimensions tweaked for...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

The parts I used: * 30mm M3 flat screws: https://smile.amazon.com/gp/product/B07NWL5HK3 * 16mm M3 hex screws: https://smile.amazon.com/gp/product/B014OO5KQG * M3 nylon lock nuts: https://smile.amazon.com/gp/product/B07GNXDQJZ * 20mm CR-10 springs:...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

It's now less expensive to build (when building 3+), more water resistant, and offers more space for alternate battery options.https://www.printables.com/model/297089-meshtastic-solar-base-station-node-enclosure-for-3---Build a complete Meshtastic...

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches...

This sword model is a more realistic redesign of the Master Sword from The Legend Of Zelda game series. The text on the front of the blade translated from Hylian says, "The Sword of the Hero of Legend" and on the back, "The Blade of Evil's Bane." ...