dan wesson shell 3d models

Details are on but will need supports and will likely be very fragile.Print separately:borealis_keelborealis_iceterrainPost-PrintingIce TerrainPrinting out the terrain with white filament works well enough, but I've attempted an interesting technique...

(Also contains STL files, as I'm mostly changing existing stuff...)Design changes:o added slopes for more strenght to the base of the y axis, also added stops to the front to prevent the rods from sliding outo designed a printable idler wheel to...

Slicing software was showing a small gap when printing with two perimeter shells. Please ensure that you have a relatively low minimum infill distance to get a better surface strength and finish. Updates - 25/06/2017 Conversion of honeycomb holes to...

It took around nine hours to print using four shells and zero infill. Approximately 85 grams of plastic were consumed during the process. -NITTY GRITTY DETAILS- To set up the holder properly, regardless of the intended viewing angle, users need to...

this is designed to fit underneath hopefully any Hornby 0-4-0 shell. as part of this, I've included a back piece, and two front's with and without cylinders. there are also two versions of each piece, one for Percy wheels (15mm Dia) and for Duck...

This mask shell was built as my Mark II design but it also serves as the main piece of my Mark IV and Mark V mask designs. For the Mark II, I print it out and thermo-form it. I use adhesive-backed craft foam to make a simple gasket. I use some...

Gone is the umbilical cord, and the clunky control box. This change could expose live mains voltage wires and terminals. While the leg with integrated power connections have some shielding, it will not prevent users from reaching and touching wire...

I made a shell around that. My reference geometry was a bit off, and the subsequent changes made the native CAD file a disgusting mess of shame and misery. But the design works now, which is all I could ever ask for. Extra info I'll update this when...

UPDATE 0.3 11/21/2015 - cut 001 T60B-helmet into 9 smaller pieces to make it actual printable (ATTENTION: single-shell model) - reworked 013, 014, 016, 017 to make the model working with an actual joint UPDATE 0.2 11/20/2015 - reworked 008...

I quite liked HorsEngineer's extended hammer here, but the number of tweaks I wanted to make sort of spiralled out of control, constituting a redraw more or less from ground up, although there are a lot of similar dimensions:...

It is a high-poly model, with a high number of polygons that create the superb outer shell of the 3D model.The model consists of 44 parts, all saved in STL file format. The files are corrected in Netfabb and absolutely error-free. If you need help...

The “ensure vertical shell thickness” setting should be disabled for lightest weight.Set a cylinder modifier around the hub with 20% cubic infill, to provide some structure connecting the drive hole with the rest of the...

(V2 version is not finished or tested). EQUIPMENT SUGGESTED (The links are just suggestions, there can be other compatible options): 4 x 380/385 brushed motors 380SA-3065-55...

 The shafts are 15.6mm diameter with the outer shell and and inner shell.  At level 4 to 5 the natural flex of that many joints, plus the flex of the plastic becomes noticeable.  I should note I am working with several generations of...

The Heart.svg (2d) file was simply loaded into openscad and extruded like this:ranslate([0,0,rubber_base_thickness]) linear_extrude(text_thickness) scale([s,s,1]) import("Heart.svg"); (where s is an optional scaling factor).Stamp 3 Rubber Hearts.stl:...

You can pay with PayPal or your credit card.Also, you may like other Busts 3D Printing Miniatures as well as 3D Miniatures Marvel and Villains._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set...

and printed on an Ultimaker 2 in PLA material.Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1...

The bed is designed in a 1mm shell mode trying to reduce the weight as much as possible, but will probably be less strong than front and cab. So the bed for a 290mm wheelbase, the one i share this time weights about 100g only. The front part is...

and printed on an Ultimaker 2 in PLA material.Note: To maintain model quality, do not try to increase or decrease the size, since the connectors may not fit and the model will not be assemble after scale changes.To avoid printing problems, we...

You can pay with PayPal or your credit card.Also, you may like other Villains 3D Printing Miniatures._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D...

You can pay with PayPal or your credit card.Also, you may like other 3D Miniatures of anime heroes._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model...

and printed on an Ultimaker 2 in PLA material.Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1...

Print Settings ------------------ I printed using ABS with 7 shells/walls, and 20% gyroid infill. All parts are designed to be printed flat on the bed with no supports. Assembly ------------- To assemble the MegaSphere, first start by...

and printed on an Ultimaker 2 in PLA material.Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1...

You can pay with PayPal or your credit card.Also, you may like other Villains 3D Printing Miniatures._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D...

that are the fallowing... Quality layer height: 0.2 Shell wall line count: 8 top layers: 8 bottom layers: 8 Infill Infill density 40% (the upper is better done in 100%) infill pattern: cubic support generate support: Yes Build plate adhesion build...

Printing: Everything is PLA, printed with a 0.3 mm nozzle, a 0.15 mm layer height and 0.8 mm shells and 16% infill. Base: Print with bottom on the bed, with supports from the bed because of the undercuts in the bottom. Cover: The cooling...

Different layer orientations/patterns  and infills could be tested.I did stick to PLA because I have no experience printing other materials yet.Assembly and testingIn order to test the replacement part, the mixer has to be re-assembled, which means...

Possibly the paddlemod would not be needed in that case as several Paddles have metal frames on those?Further feedback on fitting requiredTesting with "non-default" adjustments of the paddlesBugfixing (?)A PaddleMod with combined ShiftPaddles,...

Use 3x12 mm or longer screws to hold the shell together. The PCB's for the A/B and Start/Select-buttons should be cut to 30x45mm and 30x48 mm respectively. Take care to solder the buttons in the right spots, using the picture of the internals as a...