dart zone pro mk 3 3d models

This carriage is designed to adapt a genuine E3D Chimera+ hot end to the Ender 3 Pro. It uses one 4010 box fan (stock ender fan compatible) and two 4010 blowers (stock ender fan compatible). This is intended for the air-cooled version, I do not...

I have an Ender 3 Pro with the rear mounted electronics box by Teaching Tech. I wanted to add a second stepper on the Z axis, but needed my power supply to be in the front. I inverted the original part and removed the wiring guide as it is no longer...

Since I recently mounted a BLTouch on my Ender 3 Pro, the mechanical Z-axis end switch is no longer needed by me. It has now been converted into a filament runout sensor and a small housing has been designed for it. The case does not have any...

Want to make a part which clips onto the built-in touchscreen mount for the Ender 3 S1 Pro? This project contains: * STL and STEP files for the required mounting hardware * a build123d parametric python file which generates the models, in case...

Human: A simple yet updated Surface (Pro) 3 pen holder clip receives a modern twist. An updated version eliminates the necessity of printing with support and incorporates an extended hollow section for secure clip retention, minimizing the likelihood...

I have my Ender 3 Pro situated on my desk slightly behind and to my right, and it was getting really annoying to have to roll my chair backwards to check on the status of a print. So I created a quick swivel mount which allows for adjusting the...

I recently moved my Main Board and Raspberry Pi to back of my Ender 3 Pro with this remix of Teaching Tech's rear case. That left me with tons of room in the front for storage. I remixed these drawers to make room for two of them side-by-side. I...

This is my IKEA Lack setup for an Ender 3 Pro with a SilverCrest SDA 350 food dehydrator as filament dryer. Print settings and material selection is up to your experience, but you can see my recommendation below. ... BOM: - ...

This mod replaces the stock Ender 3 (Pro) mainboard case with one designed specifically for the MKS Gen L. If you're interested in learning more, I recommend checking out [Teaching Tech's](https://www.youtube.com/channel/UCbgBDBrwsikmtoLqtpc59Bw)...

--- Hey guys, For the Ender 3 Pro, pulleys are now unfortunately pressed onto the steppers' shafts. To address this issue, I designed a Pulley press for both x- and y-steppers. You can put the stepper into the press using a M5x40 screw and a M5 nut...

This mount is intended for dual extruder Ender 3 Pro setups. While it is designed to allow the use of the original stepper mounting screws, I do suggest getting slightly longer screws as even though it's only 0.5mm thick, it will make them easier...

I remixed that design to fix my Mingda Rock 3 Pro. Check the original thing for the spool - https://www.thingiverse.com/thing:4261119 <b>You will need (2) 608ZZ bearings</b>. I used these the last time I ordered a set. They're cheap and they...

Wenn Du bereits eine hast (von Ender 3 Pro), wird sie nicht benötigt.Spool Holder Washer.stl --&gt; Das ist die Beilagscheibe. Diese wird nur dann benötigft, wenn die Verbindung irgendwann mal locker wird.. Ich habe den oberen und unteren Teil in PLA...

I wanted to utilize a full-size SD card on my Ender 3 Pro, but every adapter I could find was misaligned in a way that without twisting the ribbon cable, the card label would be facing away from me. This mount offers room to twist the ribbon cable -...

If you need it for the left side, just mirror it in your slicer. Edit: 8/30/19 The two cases were a bit too tight to fit, so I removed one edge width from the cases and bottom drawers for a better fit under the Z rail. I recently moved my Main Board...

I had a spare Microsoft LifeCam just collecting dust and thought, why not mount it to my Ender 3 Pro? However, I couldn't find any mounts or brackets that caught my eye. I also had a metal gooseneck tube lying around and wanted to incorporate it...

I wanted an enclosure for my Ener 3 pro to print ABS with greater ease. I required a thermal blanket, but it needed additional support, so I designed the Longarms to hold it in place. The spool holder posed a challenge, so I created a holder that...

It is a direct fit on an Ender 3 Pro with no additional modification required using the original fan screws. V2 UPDATE : - Removed top of screw holes to facilitate the removal of the shield when changing nozzles. The screws do not have to be...

Simple 235x235 bed level test for the Neptune 3 pro that takes up the whole bed, so u can make sure you have the whole bed dialed in, first use the single centered test to dial in your z height, then use the five square test to get the whole bed...

After experiencing problems with the stock Ender 3 Pro's TPU filament getting stuck and not extruding, I discovered a helpful tube and bracket that aligns the filament path, reducing resistance as it approaches the hot end. The tube is secured by a...

This is intended for the Ender 3 Pro, but will probably work fine on other printers with minor tweaking.My goal was to keep most of the ports accessible.The internal USB one may be usable with a 90-degree USB cable.Ferrule connectors aren't required...

This part is intended to space out the z-axis motor from the metal structure on the Ender 3 Pro 3D printer. Over a long period of time, the stock spacing of the z-axis metal rod can be bent from too much pressure applied by the horizontal gantry. ...

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

This is my IKEA Lack setup for an Ender 3 Pro with a SilverCrest SDA 350 food dehydrator as filament dryer. ...Print settings and material selection is up to your experience, but you can see my recommendation below.</p> <p>BOM:</p> <ul>...

The original model didn't quite fit my Ender 3 pro, so I designed this one which fits very nicely. I have 4 files: 1. Ender3VSlot - use this for most of your extrusions. I laid mine flat and scaled along the Y-axis (turn off uniform scaling) to...

I recently got a Mingda Rock 3 Pro and while I'm loving the printer, my z sync belt was so loose it wasn't doing anything. I'm not sure if the belt stretch or if the previous owner replaced the belt with the wrong size, but I needed something to...

This is my Ender 3 Pro base I made to add extended feet for my 500mm tall mod from EnderExtender. I call it my "Ender TREE mod" Each foot extends about 20/25mm out by 30mm Tall. It allows better air flow for main board and mods to under my...

3.1 version Bltouch housing mount for the Creality CR10s Pro. Check out my video here: https://youtu.be/iJjqOUlZHUw. Long Version Added 12-21-2020: Use the long version if you want the mount to protect the probe when retracted. Four M3 nuts and four...

This design relocates the PSU plug to the back of the Ender 3 Pro. The design is intended to minimize the footprint of the printer overall. With the plug in the rear of the printer, the rigid end section of the power cable extends only to the...

I remixed three camera mounts to make them work with the Ender 3 S1 Pro. You need 6-7 M3 20mm screws, the two screws that are in the corner of the printer and the hing + screw from the c270. What you need to print: 1x camera mount print 1x...