draft 3d printing

It's nearly impossible to print the 287 doors straight, but you can use sandpaper on a flat surface to get them straightened out. To smooth things out, just run a file along the groove for the frame and make sure there's clearance. If you need to...

My Atik 414EX has a back-focus of 13mm from the T2 ring to the imaging chip therefore my "out of the box" STL file prints an adapter which is 45.46mm minus 13mm = 32.46mm tall. This will be okay for you if your camera has a back-focus of 12mm to...

The number 2 frustration was finding the optimized point of balance between the strength of the printed part and the clamping force necessary to keep the motor in place. Long story short, I couldn't find it! I only have PLA at my disposal and if I...

As you likely won't be able to buy parts in "singles" print a few of these to make more around your home and or give to friends. Should still come out cheaper than buying one of the branded versions and will be batteryless with more virtual walls...

......They are to be printed with filament that changes color with temperature and assembled with a watertight plexiglass covering. A stopper to plug the hole is also included in the design. By filling the models with hot water, the plastic changes color.

The whole assembly of case front, case rear, lens cap and connector protection cover is a single component print in place. It must be made with a flexible but durable filament like TPU. I used a bright colour so as to easily spot the device if...

When I paint it I will post photos of how it looks, because I intend to paint that piece of plastic the same color as the body of the blaster, not the barrel.Included in the files is a small cap tube piece, it is an optional print. It can be painted...

Here's what you need: * Hemera with square Nuts inserted in all 4 Holes on the correct side * 4x M3x8mm for attaching the E3D Hemera to the Connector (don't use longer than 8mm screws!) * 2x M3x12mm for locking the two parts together (can be a bit...

I designed this around the hexagon 2m standoff screws that came in the box with the DVR, they are 4mm but I increased the hole size to account for printer inaccuracy, on my print they fit snug. The standoff part of the screws should be the same size...

Print the "Dual Extruder Calibration GRR X350"-object- The slanted corner helps to remember the orientation on the printbed.- Select the T0.stl for the first extruder.- Select the T1.stl for the second extruder.- The object is designed for a 0.4...

This provides a much more accurate temperature reading during daylight hours. The shield consists of several parts: Several rings that are open in the middle for sensor equipment Solid plates to shield the top and bottom A larger top plate to...

Although these files have not been extensively tested through printing, they are intended to be resized to match common modelling and miniatures scales. Target scale       - Scale STL files to:       - Notes 1/3900 - 0.25641026 (25.6%) ...

... Print Settings Supports: Yes Filament: GIANTARM PLA, Feet: TPU maybe? Notes: No supports unless the one on the coat youll see on the picture. Be sure to print the coat upside down. Category: Art

Printing in PETG with an added layer of conductive material inside (connected to output ground) might help. Filling insides with some insulation compound (paraffin, for example) could also be beneficial. ## Construction The design consists of six...

After this, and a number of previous upgrades (see my other posts) the print volume reached new maximum: X=192mm, Y=218mm, Z=194mm per nozzle. The distance between e3D nozzles is 23mm. I finally got rid of the original connector PCB that was always...

commits since fd02 version - For details see [github changelog](https://github.com/freakydude/Marlin/compare/v2.1.0.0.swx2-fd.02...v2.1.0.0.swx2-fd.03) ## Changelog from 2.1.0.0.swx2-fd.01 to 2.1.0.0.swx2-fd.02 Reason for this new version is, that I...

the smaller Knob is one from radio shack that Ive had for a while, there are other examples you can print elsewhere on thingiverse Keycaps are YDMK SA Carbon blanks from Amazon LEDs: a. on the 'Small' version I used 3mm low intensity red ones -radio...

If your light switch is not blocked on one side or the other I would recommend printing the Right adapter as this requires no work modifying the scene switch. ==================================================================== The right...

I bought it in 15m length (see photo)2 - this adapter to screw onto the thread of the DYKA inspection window3 - the flat gasket to also be printed and adapted to this part to ensure sealing with the DYKA inspection window4 - the rubber part mentioned...

Instructions: Step 1: The cylinders are printed as a group to prevent problems with bed adhesion. You can separate them by cutting the connections with a hobby knife. Each cylinder has a slot on the back to help position it properly on the center...

Демонстрация как работает лампа не вижу смысла, небольшое демо литофании: https://youtube.com/shorts/4aM92jkRUts?feature=share +++++++++++++++++++++++++++++++++++++++++ What you need for assembly: It is desirable to print from a more resistant...

Originally published here: Titania with approximate topography scaled one in ten million by tato_713 - ThingiverseNot to be confused with the moon of Saturn Titan. This model is not based on a topographical map, there is not enough good images to...

Helper variables are provided to assist you in positioning these holes relative to the PCB, if your holes are for PCB-mounted components. When you are ready to print, adjust the values in the "STL element to export" section, and export each part one...

... can be found at https://github.com/dewhisna/TB6600StepperDriver and boards can be ordered from https://www.oshpark.com/shared_projects/tKN4X7AL. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 35%

This will print support-less, but you may need to sand the elephant foot on the edge of the battery clips that touch the build plate so that the battery will slide in smoothly. Also, I used a bit of duct tape (sticky side down) inside of the clips...

The PINDA probe on my machine has turned out to be unreliable, resulting in left and right steppers becoming misaligned during numerous prints, requiring me to lift both sides until they collide with the upper bracket. I would also like to begin...

But if it doesn't fit and you want the base to fit a specific casting please send me the dimensions indicated here: https://imgur.com/5T6mb2L The cars I used in the photos: - Nissan Silvia S15 (Hot Wheels Premium) - Honda S2000 Custom (Hot Wheels...

The 4 printed circuit boards with LM358 are required to be able to integrate the measuring device into the positive supply line, since the measuring devices can only be integrated into the negative line of a load without the additional circuitry,...

As you may see the printing didin't go very well so I will print the frame again and take new pictures. I decided to use an Arduino Nano as controller because I like it, it's easy to code, it's easy to find online and it doens't require big...

You can find a video of the project here: https://www.youtube.com/watch?v=5cPBAVjJ8IM&feature=youtu.be When printing the duct, I laid the small opening flat on my bed. I'm not sure if this is the most efficient way to do things since I did use...