edit stp file online 3d models

Make sure to orient these parts in your slicer, as the STL files are straight out of CAD and not on the most efficient plane. You may notice some supports designed into the front extensions; they can be removed easily and make all the difference. I...

UPDATE 12/23/2020: There was a problem with the previous files. I made an adjustment for better clearance, but did not do another test print (bad mistake on my part. Sorry about that). The result was that the bearings wouldn't fit on the design. I...

If higher gear ratios are needed a 2nd set of gears will be needed, this design uses only one planetary gear set.\n\n \n \n Update Log\n10/22/2016 Added a 1:9.8 gear ratio, 3" (77.4mm) gearbox, which pushes the limit of torque possible with thin PLA...

... settings:Material: PLA, PETGLayer height: 0,15mm or smallerInfill: 15%Perimeters: 2Brim: no, maybe for the small ball-halfs and the connectors. It depends mainly on your bed adhesion.Support: only for the cage (aready included in the 3mf-file)

There are base files attached for Bosch and Makita (at this time, working on DeWalt and Milwaukee) The TS100 is rated at 17W-65W and I haven’t seen anymore than around 3 Amps draw in testing. Update on testing - I had our manufacturing department...

It is labeled V29D in the thing files section. Originally, I put the version number on the whistle to tell them all apart as I was developing them. I kept it on the final design because it became part of the whistles story for me. Recently, Fusion...

It might be overkill but it's definitely sturdy. For the rods and bushings you will need two each per lifter unit: Misumi Straight Precision Linear Shaft - PSFJ12 THK Long Linear Bushing - LM12LUU For my printer I used PSFJ12-455 Rods. To attach the...

# License [Creative Commons - Attribution - Non-Commercial (CC BY-NC 3.0)](https://creativecommons.org/licenses/by-nc/3.0/) # Changelog 2021/04/15 - Update readme instructions 2021/04/14 - Updated design files 2021/04/11 - Initial commit ## Design...

Folders and archives have very easy to understand names.Also for your comfort there are Readme files in every archive with the description of what this archive...

Instructions --------------------- **3D Printing** 3D print one copy of each STL file. Tip: Print all the cookie cutters for level 1 in one color, the level 2 cookie cutters in another color, and the level 3 cookie cutters in a third color. This...

All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are all printed together with a color change at layer 9 (if printing at .12mm) to transition from the metallic buttons to the...

... useful. Update 4/24/2016: I added a capacitive sensor and changed everything accordingly. This seems to work really well, letting me ditch the touch sensor technology. Update 4/19/2016: I added the Step files in case you want to remix my work.

I used plaetti's Airflow Cooling Duct (https://www.thingiverse.com/thing:3376186/files) because it fits and clips on better than CarstenD's and Filboyt's Ender 3 Vent Ring (https://www.thingiverse.com/thing:2912394). However, I found the Airflow...

I've organized the STLs in to ZIP files, so you don't print the 114% scaled version accidentally, or the individual pieces for gluing when you don't intend to. Print Instructions: Stein, Lid left, lid right, lid screw. Print at 0.2mm...

Secondly you can just using a file or something similar to clean up the sides, but it’s going to take longer and probably won’t yield as good of results. For the last part you will need a heat source. Heat the nut up on the bolt or z axis rod and put...

... The difference between the two files lies in the fan mounting holes, m3 or m4. Use the one that fits your screws. All fan and tab holes (except the bottom tab) are pre-countersunk. M4 fan screws may experience clearance issues with the power plate.

Print direction: profile facing sides should be on the bottom for best visuals. Bill of material ================ Test print some files before buying stuff, a good and accurate printer is required. Maybe settings have to be adjusted for the press...

20200827 added sticker decoration as svg and pdf 20200706 fixed Bug in boat_cover.stl 20200702 added hull without batterymount 20200701 initial upload Additional 3D Models: none Object License - Standard Digital File Store License Remixing Not...

Please note that the disc pictured has 6 slots as a tribute to the hyper-rare "Fight Disc for Card Games" seen here, while the files provided will make a traditional 5 slot duel disk: https://yugioh.fandom.com/wiki/Fight_Disc_for_Card_Games My...

I made STL files available for both a single wedge and a three-wedge assembly. It's essential to note that these wedges are not recommended for installation without proper knowledge or guidance from a qualified bike fitter, as misuse can lead to...

Slicer supports are minimal for the two parts, therefore, no presupported files are included for this model. If you have the proper filament colors, no painting is needed.As presented, Tails is in proportion to my previous Sonic model.Tails can be...

For the front: 8mm-----------------------------------------------8mm 8mm-----------------------------------------------8mm 10mm door bridge --------------------------- 10mm door bridge 10mm----------------------------------------------10mm...

Airsoft Claymore Mine | Prototype **Don't bother downloading the file, it's only the detonator pin.** I am now entering the prototype testing phase of my latest claymore mine concept. This is not a final design, just a prototype to test everything...

0.2mm layer height, 20% infil 300x300mm bed was used, Things to do: - Re-orientate STL files to match intended print orientation. - Re-design the spring rod to be printed horizontally and in less parts - Selector is a little loose, may need to...

Here's what you need: * 6m GT2 with 2mm pitch belts * 1x 1040mm closed-loop belt (520mm perimeter) used for dual Z * 2 x 200mm closed-loop belts (100mm perimeter) * 4 x 20-tooth idler pulley with 5mm inside * 2 x 20-toothless idler pulley with 5mm...

If it doesn't file/sand the post so it does. If you are using the side holes with tightening bolts you will probably require 20mm long bolts. Be careful not to over-tighten or you will break the plastic. **Warning:** _If you forget to apply the...

In this way, at the end all the pices are flash. Also i recommend to glue these pieces in the Prusament spool. The disc Print the first layer at 0.15mm so that il will be as little as possible material between the magnet on the dart and the nuts in...

Don't print the files 54-59 and 82-93This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer Height: 0.3 mmLine Width: 0.4 mmWall Line Width: 0.4 mmOuter Wall Line...

I've included STEP files for reference and modification purposes, ensuring that users understand the licensing requirements. Selling the Taipan without permission is prohibited; interested sellers should contact me directly. Tips are greatly...

The pictured pouches are my printed prototypes so please ignore the issues you'll see (I love the amount of P's in the last sentence), with the findings from the prints built into the files shared (I'll be reprinting at some point). These...