eg models

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

It does not need power to work, it is simply a switch that opens when the sensor tip touches a surface. It is probably NOT suitable for a 3D printer bed leveling system because it could touch the model you are printing. If you added a removable cap...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

If they are different, please update the Fusion 360 model and re-generate the toolpaths. Also, if you plan on using different tools for the above operations, make sure you update the tools (and associated feeds and speeds) and regenerate the tool...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

On homemade springs using generic musical wire When it comes to homemade magazines, the models by Thanhtacles are designed to use drum springs unlike the box springs exemplified by their commercial counterparts, for what I assume is the most...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

Buy me a coffee!https://paypal.me/SmartHelpatHome   *Buck-converter:Used in 3D printing to regulate 24V to 12V for example when using 12V fans or other electronics on an Ender 3 which is 24V native.More...

If you think you want to change it or try to understand it feel free but I can't help.NOTES:Not all parts from this model need to be printed or even downloaded unless you want to alter the design or re-render the parts using the *.scad file. Parts...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together.  It has an...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 67 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

I would also suggest allow for extra LEDs in your strips and to slide in your LED strips as you combine a segment to other segments. All in all, I learned a great deal about modeling using Fusion 360 and 3D printing using Slic3r and the Original...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Mounting: The EPL-LED-150W-RT...

3D printed parts: 8 brackets, remixed by me and provided here (original design: https://www.printables.com/model/200616-creality-ender-6-enclosure-top-cover-lid-2020-240m) 3 door handles (https://www.thingiverse.com/thing:4768759) Shortened spool...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

... one at a time by clicking Download each time. Or click Download once on the file spider__man.rar ### My some other things: Category: 2D Art