ender 3s1 enclosure 3d models

I use a concrete paver and some foam padding for my ender 3 pro to sit on for vibration reduction. I caulked all around the acrylic sheets to seal the enclosure. I also use underneath the stand for storage of tools. My filament dryer and controls are...

I'm going to need some ABS 3D printed parts in an upcoming DIY go-kart series, so I decided to make an enclosure for my Creality Ender 3. Being unsatisfied with both the cost and quality of available options on the market, I set out to DIY my own...

This is my enclosure design for the Ender 5, inspired by the Prusa Ikea Lack. The height of this enclosure can be adjusted to your preference. It's based on 25x25mm aluminum extrusions, which I used in 1m lengths and did not shorten. If you use...

The Ender 3 does come with an electronics enclosure on the front left. I tossed mine out when I moved the motherboard and Raspberry Pi to the back, opting for TT's rear enclosure instead. I could've hung onto it, but it had fittings and holes that...

Doesn't the Ender 3 come with an electronics enclosure on the front left? It does, I threw mine out when I moved motherboard and raspi to the back, using TT's rear enclosure. I could have taken it again but it has fittings and holes where I don't...

Doesn't the Ender 3 come with an electronics enclosure on the front left? It does, I threw mine out when I moved motherboard and raspi to the back, using TT's rear enclosure. I could have taken it again but it has fittings and holes where I don't...

This is my take on the DuetWiFi enclosure for the Ender 3. It's designed to be a retrofit instead of using the stock electronics enclosure. You may need to extend your wires in order to use it without limiting your maximum print height. This is an...

Add a 5V Noctua fan: https://www.amazon.com/gp/product/B00NEMGCIA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Replace all the connectors, remove the old board and run wires from the 24V out of the power supply to the 24V in of the Duet and mount...

Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere, just measure for the lengths required. ...

I've been putting in some serious time working on an enclosure for my Ender 3 Pro, and I'm finally done with it. This enclosure is different from most others because it's still a single piece when combined with the printer itself. One of its key...

This is influenced by Youtuber Teaching Tech, check his channel out for a video of him installing a similar enclosure on an Ender 5 pro. His build is here: https://www.thingiverse.com/thing:3862902 Link to hinges I used, I went with three...

https://www.thingiverse.com/thing:5111093 Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere,...

It has made a world of difference for me. I have included a doc file with hyperlinks to the SD card cable and a long control cable. I also have included the STEP files for the design, in case you desire to make changes. Print Settings Printer Brand:...

THESE CORNERS WERE DESIGNED FOR MY ENDER 3 - 25MM ALUMINIUM ANGLED FRAME STRIPS AND PLEXIGLASS PANELS 

Remix of 2 Thingiverse Designs 1: Kilroy01's Ender-5 Control Panel Back Cover https://www.thingiverse.com/thing:3353394 2: Wolfganghsu's Snap-on LCD Cover for Creality Ender-3/Ender-3s/Ender-3 Pro/Ender-5 https://www.thingiverse.com/thing:3670360...

Simple enclosure for an Ender 3 or anything with similar dimensions I used PETG but I suppose any filament would work. This is all designed around 2mm plexiglass and 13mm PVC (13mm inside diameter, 18mm outside) (1) is the top corners. Print 4...

2 parts you need to install an ender3 in a closed box: a base to hold the coil holder (with screws on enclosure top)a piece to hold the filament end sensor

This enclosure is crafted from a combination of durable plexiglass sheets and precision-engineered 3D printed components, perfectly suited for housing the Creality Enter 5 Pro printer. No modifications are required to print this enclosure on a...

This is a remixed enclosure this enclosure is taller specifically 8 inches so that it does not push down on the cables as much, the original creator messed up the dxf files and they were missing a lot of holes. some of the holes were a bit too small...

Enclouser for your 3D printer, Fits Ender 3 Designed to laser cut in 6mm Plywood and acrylic glass door in 3mm Door hinge for acrylic glass door can be 3d printet in one piece If you like, please Tip :-)

This is a remixed enclosure this enclosure is taller specifically 8 inches so that it does not push down on the cables as much, the original creator messed up the dxf files and they were missing a lot of holes. some of the holes were a bit too small...

This is a simple enclosure made using an IKEA table and some simple 3D printed parts. It is made to be used with 3mm hardboard cut to 470mm x 440mm. there are small gaps at both the top and bottom for small cables to go if you want thing like LED...

I'm building a lack enclosure, and I've decided to ditch the pricey plexiglass. Instead, I've modified the four corner pieces to accommodate a 5mm foam board - it's a great alternative to the 3mm plexiglass that was originally planned. ...The front door...

I couldn't find anything similar so I created this frame for my enclosure. It is not perfect, but works fine for me. I would advise to print a "prototype" first. The Frame fits an 18mm wall. The holes on the Front fit M3x20mm screws. The...

A very simple laser cut top for the Ender 6 Yellow mounts i made from here - https://www.thingiverse.com/thing:4718662 Handle for door i made from here - https://www.thingiverse.com/thing:4768759 3mm Acrylic - 50cm x 50cm x 30cm Piano hinge 14 x M4...

To replace Marlin with Klipper.Enclosure dimensions: 450mm (W), 540mm (H), 590mm (D)2022 May 7thI've stalled on this, after fixing my extruder last month I struggled to get any successful prints off my ender 3. After 20 attempts, I grew tired of my...

I only swapped out one of the many components in the enclosure. For the rest, check out the original: https://www.thingiverse.com/thing:3697275/remixes My DHT-Sensor was bigger than the one used in the original, so I had to enlarge the holder for...

It also aids if you desire to move controls outside of an enclosure. I found the angle of the display very bad for me with my bifocals and the micro SD card slot damn near impossible for me to get the card in. So I designed myself a housing to...

This is an enclosure requiring minimal carpentry skills and tools. It keeps the heat in, muffles the sound and evacuates fumes with the optional ventilation system (coming soon).</p><p>This is much simpler to fabricate with woodwork tools but I...

here is my full 3d printed top enclosure mod just buy the top Perspex sheet. print everything in rotation that loads on cura with tree supports for the corner parts. I printed everything in 0.2 longest print time is for the extrusions printed...