ender v2 vs s1 3d models

This is a remix of the original a drawer for an Ender 3 s1 that holds a Raspberry Pi 4 B. I removed the back storage area to shorten the drawer and added a fan mount for a 30MM fan. I also thickened the USB port rails so they would'nt break...

Print and fit adapter to make the original BBT Pad 7 mount work on the Ender 5 S1, with no changes required.V1 for now, and I will update it once I've put some print hours on it. Frame mount holes are designed for M4, I've used a printed T nut to fix...

The stepper motor cover for MrPiouPiou's bed cable angle adapter doesn't clear the bed on my Ender 3 S1 Pro - just not enough clearance. This causes the bed cable to catch on the gap in the corner of the stepper motor in the back. To solve the...

The case mounts directly to the side of the Ender 3 S1 Pro, replacing the factory display mount. The display then mounts on top of this case. Enhancements : - It offers a higher angle for the display. - It has a downward facing fan...

Of course, this could be quickly fixed with ABL, but it still felt not right.Solution:I search for possibilities, also found the silicone spacers (which I ordered…). And so I stumbled upon the design of HomeGrown3D.Unfortunately, these did not...

This is a Filament Spool Bracket with Bearings for the Ender 3 S1 Pro. I used skateboard bearings that I had on hand. Special attention must be made when slicing the shaft (Cura) because Support must be Blocked for all except the top end of the...

Ender-3 S1 light bar bracket. https://www.ikea.com/us/en/p/silverglans-led-bathroom-lighting-strip-dimmable-anthracite-20439679/ Easy to print light bar 24v that uses the power suply port for power. This allows for the power cable to be hidden...

I finally got sonic pad for my Ender 3 S1 Pro and I had to place it somewhere. Unfortunately, Sonic Pad doesn't support portrait mode so I cant place it on side like old screen. An obvious place for them is top part of printer but I didn't want to...

I wanted a parallel wall mounted spool holder, and I like the original cross bar that comes with the mount on the Ender 3 S1, with its double set of roller bearings. The receptacle on this mount allows insertion of the original Creality roller bar,...

This model can be attached to the Ender-3 S1 hotend and bed to mount the ADXL345 accelerometer. A single M2 screw is needed for the hotend attachment while it clips on without a screw to the metal plate under the bed. Make sure to place it on the...

But I am happy with the performance so far.I accidentally printed the model below without supports with steep overhangs and a 11,8 cm  bridge and it printed beautifully at 80-180...

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

I liked the aftermarket Z-axis stabilizer by p1mrx, but the front mounts didn't fit my Ender-3 S1 Pro, and the rear mounts were too unstable. I redesigned the mounts to fit my frame (which appears different from the one the designer has), and added...

• Enable to use Filament Dryer without any MOD on filament sensor.(Empty 250g spools can be used as reel) 2023/06/26 add V2 model. V2 is the reverse of the screw winding. V2 is better for use in the orientation shown in the photo, so it will not...

A Universal camera mount for the Ender 3 S1 Pro (And other models)Simply clips on to the standard bed belt tensioner. It will work either way around, but was designed for use as pictured.</p><p>I've included a few different extension bars so you can...

You will have to scale the part a bit higher if your flow rate is higher to fit the original mount.I uploaded another version (V02) because some users found the fit too tight and there was not enough room for the cable.The component can be printed...

For example: https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offset https://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...

I modified the z arm so that it would fit onto the S1 pro. ...Remixed from the original https://www.thingiverse.com/thing:3612390

Assists in leveling out the stage

Makes the cable at a more vertical angle Still, it is not completely free of gantry interference. ... If the height of the molding exceeds approximately 220 mm, remove this adapter.

A very small and handy tweezers holder. Always at hand. ...Optimized for 0.2 mm or 0.1 mm printing.

Designed in Solidworks Printed in PLA for prototype and PETG for final iteration. the glue stick I used is 1.170 inches or 29.74mm thick. whatever infill you want doesn't matter. ...

A remix of a drawer insert without the clippers and more storage. ... I have my clippers stored on the side of my machine using this design: https://www.thingiverse.com/thing:5774940

This project was born when I have placed my printer on the open-cabinet. Original creality spool holder was 2cm too high - thats why i have designed this :-) This brand new part is using one of original parts from creality spool holder - the...

This is a foot made for an Ender 3 V2 which needs a taller foot than the normal ender 3. I bought a V2 for parts and it was missing the feet so I made these. They will work for any ender like printer with the 40X40mm base pieces. ...These are made to...

I made this as a quick fix to overcome my paranoia of the spool falling off of the factory Creality Ender 3 S1 Spool holder. While the original design is quite good and I'm happy with the ball bearing setup, the end stop still doesn't give me a warm...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...

Wanting to use my eSun eBox Lite filament dryer box with my Ender 3 S1, and looking forward to setting up an enclosure (at some point) in the future, I designed this bracket that allows for fixed placement of the runout sensor with the filament feed...

My June 2022 Creality Ender 3 S1 Pro buzzer is crazy loud, and no other models I found fit. The buzzer noise is now reduced about as much as applying two pieces of 3m vinyl wrap on top of the hole, which I had previously. So, if you have adhesive...