esp8266 case 3d models

So I was off to the races. Here is an animated closer look at the mounting solution: Full access to gas tank for refueling:Motorcycles have small gas tanks, so you have to refuel often if you're doing any amount of serious riding, so I had...

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

Easiest way is chuck it up in a drill and a bit of sandpaper, and you can use that same technique to clean up any nub tips that are out of shape.Insert the circuit board into the housing at the same time as the rocker with springs, and carefully put...

Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis doesn't get wrapped up and pull. I found the following information about GRBL...

Taking a look at the stock version of the mini vise, the adjustable jaw (in my case) rides in a slot that is about .030" too wide and binds as it advances or retracts the jaw causing as much as 4.5mm lateral movement of the jaw (arrgg). Also looking...

The setup should allow you for a 270 degree swivel of the display if you use the special bracket... ...This will come with a BTT TFT7 case, so I also did this for the 7inch display: https://www.thingiverse.com/thing:4883408 ,but you should also be...

In my case, I have used a Bigtreetech GTR v1 / M5 board, with a lot of Marlin configuration in order to get it to work. I only describe here the mechanical changes you need to make, and if you are not familiar with getting Marlin to work to a...

There is one part I recommend printing at a smaller layer height, which is the net, as it has very small details and it'll look better, I printed it at 0.15mm.Infill: 20% for all the part minus the pole which I used 100% to make it a bit heavier and...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Add a touch of glue to hold the nuts in their sockets on the Top piece just in case the screws should come loose later for some reason (once assembled it's hard to access them). Attach the Finger Board to the Neck. I did this using the tight Fret...

That's much more robust in my opinion.In my case the used Guides and the used Guide Blocks are less noisy than the original Linear rail parts.The Mainproblem are the Guideprofiles. Mostly you get only a length of 350mm but you need 330mm long...

Any amount of support is greatly appreciated :-) paypal.me/BrianBrocken Feel free to take a look at my other designs: 3D printable antweight battlebot: Bulldog: https://www.thingiverse.com/thing:4623536 SpaceX inspired edf rocket:...

In my case, it's off by a hair (as you can likely see in the pics) so I will need to shim inside the guide for more accurate drilling. Intent here is to ensure that the wood is in line with the fence and isn't pushing the work piece away from the...

If your Y and/or Z axis limit switch positions are not adjustable, as I understand to be the case for some printers, you will need to find and install an upgrade(s) to your printer to allow appropriate Y and Z axis limit switch tweaks before...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Operate the motor for a short time at low pressure to avoid jamming in case some glue entered the cylinder. Repeat for the other cover.Figure 9: Assembled motor with some Lego Technic parts.If all goes well then the motor works as intended,...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

It is used to tranport the excavated soil to the surface and serves as an evacuation route in case of emergency. To further drive home the message that 3D printing can be an efficient mean of manufacturing, these modular habitation blocks can...

But if they are out of stock you can also find the pricier kpower brand which is the same servo on Amazon KPOWER 3kg/0.07s Coreless Titanium Gear Full Metal Case Slim Servo for RC Airplane Heli https://a.co/d/50YJh2K Another good option:...

Optionally you can print as many intermediate stages as you wish in which case it is better to have one intermediate stage with a guide loop and print the top stage without a loop. Print the nose cone. A simple hemispherical nose cone is included...

Well done! Taking things the extra mile You will need:hair spray (there's a good chance you already have one nearby your printer)glass jar big enough to accomodate the ballglitterIt is quite important to have the glitter and filament color...

The axle is now held captive between the two halves of the case so no longer sticks out the side (as in V1). * Revised Elevator pot gear. V2.stl - size reduced to fit in the new enclosure, and fixed an error in the pressure angle to match the trim...

In case you need advice where to get your filaments from, check our partner's website. Speed setups: Infill speed: 30mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt...

X-axis Belt Alignment (optional): In my case the tire gauge mount would not hang freely when butted up next to the extruder. Anet provides two M3 x 18mm screws to mount the X-axis belt to the extruder assembly. Because they are too short, they cause...

The 45º ledge is used to glue a thin LED strip or in my case LED Modules, which will point towards the bed.The factory LED strip is 24v DC, but the LEDs I had were only 12v. I ended up using a MP1584EN Mini Buck Converter, to drop the voltage to the...

Customized version of [http://www.thingiverse.com/thing:46884](http://www.thingiverse.com/thing:46884) made with Customizer! Using these options: qr_tolerance = 0.001 case_thickness = 1.8 tag_height = 80 obj = 0 qr_bottom = 1 hole_r = 10 hole_y = 0...

This may be the case if it has been rotated significantly. - This may also throw a 'WARNING: Object may not be a valid 2-manifold and may need repair!' sporadically when rendering the body including the Chute, but will still print OK. At least it...