f 35 thrust vectoring

GreenGrowBox Nicole
prusaprinters

If you measure the luminous flux 200mm beneath the led strips, you should get around 10.000 lux.Wago 221 splicing connectors: https://www.wago.com/gb/electrical-interconnections/discover-installation-terminal-blocks-and-connectors/221220V 2way, 4...

Music reactive matrix LED cube
prusaprinters

This will not end good… Take care… Seriously !!!All provided vu meters were set to values to take care to not drain more than the 20W out of the power supply. Use a good and secure ≥5V/4A power supply to avoid serious damage!The real question...

Budgie Sony A7-series Shift-and-Stitch Adapter
prusaprinters

A Minolta MD 50mm f/1.7 and commercial MD-to-M adapter are shown, but I've used lots of different lenses. Some vignette more than others, but most lenses seem to work with surprisingly minor vignetting. I recommend starting to frame the shot by...

Hexx Case Tool Roll
prusaprinters

With a little luck, this lands the legs on the grooves inside, and you can use a flathead screwdriver to bend them down into place.Roll it up and slide the hexagonal latch on to the track between compartment A and F.Take a photo of your competed Hexx...

MMU3 Buffer + Prusa Enclosure Internal Lid Mount (Mod 1)
prusaprinters

I found this is easier if you poke a piece of filament thru the holes to help align them.(e Replace the lid with assembled buffer unit back onto the enclosure, and secure using the previously removed 4 x M3 x 6mm screws.(f) Place spool holders into...

Color-Click-Button
prusaprinters

It is super easy and you don't need additional hardware (like the MMU).  This instructions apply for the Prusa i3 MK3 and Prusa Slicer, other printers might be different. Drag and drop the "Colorwheel.3MF" file into...

0-10V Dimmable Explosion Proof LED Paint Spray Booth light - Class 1 & 2 Div 1 - T6 - 7,000 Lumens
grabcad

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

4" Back Horn Speaker V2.0 - Bluetooth, Active, Passive
thingiverse

- You can find a somewhat more detailed list of supplies in my Instructable: https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Any combination will do (as long as the driver is 4" or smaller so it fits the enclosure -...

Customizable Triple Letter Blocks Ambigram
cults3d

The letters E,F,I,J,P,T, and Z should also have supports, but they can be printed without if you don't mind clipping and sanding the messy first several layers of the unsupported areas where supports should be used. Of course, the letters on the...

Nerf Gun V2
thingiverse

2x - mechanical relay...

Back Horn Speaker V2.0 BL2 - Bluetooth, Active, Passive
thingiverse

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

Improved lack enclosure with dry box ptfe tube connections and other upgrades
prusaprinters

I really don't like the idea of something that gets up to 500 degrees F sitting on top of particle board shelving so there is sheet metal construction glued above and below the printer god forbid that is needed. Because the table isn't sitting on the...

Dimmable Explosion Proof LED Paint Spray Booth light - Class 1 & 2 Div 1 - T6 - 5,750 Lumens
grabcad

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

Walking Dinosaur Robot
prusaprinters

The robot has a ponderous gait.   PrintingGenerally I use a 0.25mm layer height and put about 1mm of plastic on the outside surfaces as a shell.  Since my printer has a 0.5mm nozzle I use 2 vertical shells and 4 horizontal top and...

EasyCut
prusaprinters

Carefully:In Fluidd/Klipper, select {...} icon in column near left side of main page.Find and Click on printer.cfg file to edit. Then single click anywhere in file top comments, then press Control and F keys together which opens the Find prompt near...

45 Degree Surface Mount Explosion Proof LED Paint Spray Booth light - Class 1 Div 1 - Class 1 Div 2
grabcad

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C...

CR-6 LGX Lite and Dragon Direct drive mount to the CR6 strain gauge
prusaprinters

The ones with straight knurling's are no good and are meant for injection molding not 3D...

112W Explosion Proof LED Light for Paint Spray Booth - C1&2D1 - 4' 4 Lamp - T6 Temp - 0-10V Dimming
grabcad

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This 0-10V dimmable fixture carries a T6 temperature rating and is approved for Class I...

Arca Budgie Sony A7-series Shift-and-Stitch Adapter
prusaprinters

A Minolta MD 50mm f/1.7 and commercial MD-to-M adapter are shown, but I've used lots of different lenses. Some vignette more than others, but most lenses seem to work with surprisingly minor vignetting. I recommend starting to frame the shot by...

PrintBone small - 7 inch bell trombone
prusaprinters

With a Conn 48H slide, the third partial (F in first position) plays a bit higher than in most trombones. This may take some getting used to.</p> <p>what you need:</p> <ul> <li>A 3D-printer with an at least 18x18cm print bed, 20cm high</li> <li>2x...

Arduino Robotic Arm (OPEN SOURCE) + Python control APP + EXTRAS
prusaprinters

In the images attached to the gallery you will see the recommended orientation for every element to be printed.Gently remove the support once printed. The REDUCTION part is a critical part of the robot. Print is slowly.Features: Google Blockly...

Explosion Proof Emergency LED light - 4 foot 2 lamp - Backup Ballast - Class 1 & 2 LED Light
grabcad

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...