fanuc robot models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

---------- # STP FILES Again I included the STP files, so that everybody with a decent 3D CAD can load the volume models. ### The thread test STP In this file you find a test screw (with the nominal threads) which is identical to the spindle...

...Composed of two pieces - a base for the motor and a cover - the protector fits perfectly on your pistol model, keeping your magazine safe and protected throughout the action. Don't let a lost magazine ruin your play - get our magazine protector now!

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... DonationsIf you found this print helpful, sending me a...

... zip tie. (Optional) Install Anti-Skid pads on the bottom of your new drybox to help keep it stationary while printing :) If you found this model useful please consider leaving a comment, posting a make, or donating filament to fuel my experiments.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery.</p><p>You will need the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

I'm slowly printing this work of art so I hope to eventually show a working model. If you print it and find something doesn't work, please report that and I'll try to fix it. Also, if I goofed up the maze and there's no way to solve it, that would...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

... There are also useful coat hangers and finger toys.Compliant mechanisms:In case you want to know more about compliant mechanisms, check out these models from BYU_CMR.

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

For the extruder I used from: https://www.thingiverse.com/thing:2735475/files cable-holder.stl https://www.thingiverse.com/download:4650325 extruder-cover.stl https://www.thingiverse.com/download:4650320 extruder-idler.stl...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

 Note, only model files (.AMF) are uploaded, no g-code uploaded for the upgrade.This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting...

I modeled the general design of these connectors after Spears brand Dri-Splice connectors (http://parts.spearsmfg.com/sourcebook/TURFTECH_TURF_IRRIGA_T_TURF_DIR_T.pdf). Most of the good professional landscape light and outdoor audio companies in my...

Note: dimensions are in metric system (in millimeters, mm) and the model adopt A4-size paper sheets (not US-letter). <h3>Assembly instructions</h3> For the 3d printing, we used white resin for both "pointer" and "pointer+wheels". Concerning...

&nbsp;- Click on the "Download" button and you will find the download file in small print coloured light grey below the Model &nbsp;files.&nbsp;Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...