feather 3d models

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

If you want it with an internal battery, I have designed this same model with a hole for the battery, measuring 126x85x35mm, you have it here: https://www.thingiverse.com/thing:6016217 Required Components: - 1u Mini ZVS Module 5-12v (...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

You can use other sized bolts (M3 or M4) files are uploaded for adjustments, I can and will upload different sized models.* *OPTIONAL PARTS* 3x WASHERS (desired size) 3x Nyloc Nuts (desired size) #HOW TO PRINT During the design process I accidently...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

If you need a shorter version then I have one of those too, see the shorter Z axis pointer thing.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Supports:NoResolution: .2Infill:20%Filament:Amz PETG/PLAWhite Notes: Printing the...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+ THIS MODEL IS UNDER CC (Creative Commons) LICENCE. Note: The DO NOT EAT sign might not print properly due to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

 - Click on the "Download" button and you will find the download file in small print coloured light grey below the Model  files. Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...