feeded 3d models

This has been on my mind for a while now, and I wanted my daughter to witness how birds nest and feed their young. So, I decided to build a "Spy Cam Module" for bird nests. It's a relatively simple print. To get this up and running, you'll need the...

Feed the motor cables carefully through the mast. Make sure any sharp surfaces are filed smooth, including the inside of the motor mount where the cables run. 3. When the motor is attached in the correct alignment and position front/back for the...

Feed the power supply connector through the hole in the bottom of the case from the rear and pull the cable through. 2. Insert the power supply from the bottom of the case with the power pins facing towards you. Push the power-supply until it is...

* Feed the cord through the usb cutout in the 3d-printed case. * Place case foam, if desired. * Cut the gasket material to size and place in between the plate and pcb at the top and bottom of the case. (The sides do not use any gasket material.) ...

The dispenser is designed to allow eggs or sweets of up to 35mm (max) in any dimension to feed out through a chute in the base of the egg. Just rotate the top two parts of the dispenser (screw together) to open and close the opening into the base...

It may take a few turns for the tap to feed through smoothly. To install the Sonoff board, arch the back of the housing slightly to spread open the two ends, then snap in the board. The notches on the corners will hold it securely in place. I...

FYI for the "Curious" I use two DC feeds from my Power supply, Controller and Heated Bed, both separately fused at the power supply (proper method) and using different wire gauges. ...I used 2x M4 x 35mm hex head bolts, frame makes it hard to use...

Secure the flight controller, connect the 4 motor wires, and feed the battery connector through the top. Finally, attach the top plate assembly, use a rubber band to secure the batter, and voila! Please stay tuned! I plan on creating an updated v2...

This essentially becomes a make/break/make toggle connection preventing the sources from back feeding each other.I wanted put this up available to others as it is since it's in service for me now and works but I have plans I'll be working on shortly...

Watch this video for a basic intro: https://www.youtube.com/watch?v=3hq6JWKJVJ0  All of the parts are scaled for 40mm tall super-soldiers in heavy armour.To obtain 32mm tall miniatures, scale all parts down to 86%, or 28mm tall to 81% Modular Hero...

Instead, spiral wrap the cables and feed them from the top/back side of the chassis for a cleaner and more open look. The carriage is set up for a short NEMA 17 motor (part number 17HS10-0704S, but should also work with the smaller pancake). ...A spacer...

It helps if you loosen the bottom #10-32 screws a half turn or so.Take the spacers and feed them through the “clips” on the bottom rear of the mount. Push them up or down through the opening, do not attempt to push them in from the side and “snap”...

Compared to V2, it holds one round less but (among other improvements) provides better feed angle, making the whole loading process smoother. It uses a standard Glock 17 magazine spring. I dropped the option to use HK 17-round spring - it provides no...

You will learn to work around this by either cutting them into (still large) chunks, or starting to feed them into the shredder by hand. Don't expect great results trying to mulch up dry plant matter (corn stalks, leftover annual/perennial foliage...

* Feed motor extension cables through Cable chain. Filament Guide: * Insert 2 M3 nuts, using M3 x 8MM screws attach the filament guide to the front two holes previously used to mount the extruder in the factory location. * Screw PFTE fitting into...

I decided that I needed a top-mounted spool holder to feed the pseudo-direct drive conversion I created for my Kobra Plus. I also decided that I wanted this spool holder mount to have the ability to accessorize. This is the end result.The spool...

This "Gun" uses the Venturi Effect (Caused by the gas from the air duster flowing from the narrow internal nozzle into the larger barrel) to create a vacuum in the vertical ammo tube and "Suck" BB's into the barrel, making it much more reliable than...

The feeding habits, physiology and potential speed of Tyrannosaurus rex are a few subjects of debate. Its taxonomy is also controversial, as some scientists consider Tarbosaurus bataar from Asia to be a second Tyrannosaurus species while others...

The exit manifolds from one socket feeds directly into the entry manifolds for the next socket. As it makes it way around the cans, the coolant picks up heat and is ejected via the exit port. As always, if you have trouble removing the cans push up...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Removing anything was not an option and keeping the filament run-out sensor was absolutely a must, so this design evolved to V3 (currently in use) and V4 (offering more stability - hopefully...). See "Post-Processing" and pictures for fixation....

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

The rest can be printed using 40% infill. Program the Arduino Pro Micro following the instructions in the provided file. Glue the nuts into the mounting points on the back of the front cover. Wire up and push the lever arm micro switches into the...

I wanted to put a desiccant and hygrometer on the filament, so I tried a few things to put it all together. ・Compatible with spool holes of 35 mm or more in diameter and 65 mm or less. ・By inserting a short PTFE tube at the bottom of the filament...

I'll leave you to make your own choices with the rest of the settings.This is quite a big ring, and the switch I used was intended for manual operation.You could feed wires into the ring through the switch hole if you wanted to use an external...

The second fan (Left side) wires feed through the duct, then up and over the hotend. <strong>Yellow is positive on OEM wiring.</strong></p><p>You should have no issues triggering the X-Axis end stop switch, but if you do, bend the end of the little...

... red and look for any area where the paint is wiped off from contact. The input hole for the filament may also need to be cleaned up with a drill if the filament doesn't smoothly feed through in both directions (especially when changing filaments)

Feed a wire through the channel, remove the isolation and put one or two knots in it to give it a bit more thickness (keeping the wire quite long is really helpful here). You can use a bit of glue or slightly melt and press in the print with a...

cobee Plastic Syringe with Tube 100 ml Large Plastic Syringe with 130cm Hose Tube Large Plastic Measuring Syringe for Feeding Watering Nutrient Measuring Scientific Labs Glue Applicator Experiments https://amzn.eu/d/06IIjrI How to use: 1. Cinch...