finger loop knife

Interlocking Sorting Cups (Hex Shape) - Version 2
prusaprinters

A good rule of thumb is this: Using your thumb and index finger, if you need both hands to make them click, you are in a good spot. If in doubt, go for the tighter fit.</li><li>If none of the test prints work for you, try another filament or...

Streetwear Girl 1-16 - Sportswear Girls Pack Game-Ready Low-poly 3D model
cgtrader

Fully compatibility with Epic Skeleton - including solved Mannequin problems, such as incorrect rotation of fingers, etc UE4/UE5 projects with playable character blueprints and clothes, body physics simulation - plug and play! Unit: centimeters. All...

Apple 1 Replica-1 plus Case
prusaprinters

...  Either use tape or your fingers to temporarily hold them in place while you place the top half onto the bottom half by first locking the right side into the small clip slots.  Then tighten the screws. The screws will cut the threads. it.

MultiClip Object Mounting System
prusaprinters

There are two versions available for left- and right-handed operation. You can also use them to properly align your clips with a levelling tool or to protect your fingers, e.g. ...when using a stapler.<br/> Bar width of the helpers is exactly 1cm.<br/>...

Streetwear Girl 2-14 - Street Wear Girls Pack Game-Ready Low-poly 3D model
cgtrader

Fully compatibility with Epic Skeleton - including solved Mannequin problems, such as incorrect rotation of fingers, etc UE4/UE5 projects with playable character blueprints and clothes, body physics simulation - plug and play! Unit: centimeters. All...

OMP M2 conversion, Revell 1:32 scale Huey
thingiverse

Make sure that you do not invert the pipette with glue in it because your finger heat will boil the glue, which then can come shooting out of the pipette. Don't ask me how I discovered this ;) NOTE: When gluing the body halves together, DO...

Auto-rewinder stand for Rubbermaid 16 cup container
prusaprinters

Grasping the ends of the axle with your fingers, drop the ends into the slots on the stand support arms. Thread the filament through the M6 fitting. Put a paper clip on it to keep it from retracting, until you load the filament into the printer. With...

BattleSTAR - The first and last 'GAMING' headset stand you'll ever need!
prusaprinters

Just buy rubber sheet online and use the provided template to cut them; LABOUR IS NOT CHEAP AROUND HERE!) < Injuries such as cutting your fingers are not our responsibility! ></p> <p>It will only cost you 22 hours of your life and maybe a...

Magnatic Stirrer
prusaprinters

Than take you fingers and press it down so that you can press the motor from the other side threw the hole from the bottom. So now you take some tape and tape the srew to the srewdriver, because if you don't do this you won't have chance to fix the...

TARDIS LED Lamp
prusaprinters

You'll need 8 of these. Assembly InstructionsOnce everything is printed follow the steps below.Please note, much of this will just push-fit and clip into place, but some parts such as the door handles, keyhole, and possibly the windows, may require...

A spring-loaded RC plane wheel that really works
prusaprinters

;)Better idea: Put one wheel (rim and tire) on an axle (drill, pole, etc.) and push it down on a bathroom scales with two fingers. First test: The spring travel should not be used all the way down until you reach about 4-5 times your model's...

Magnetic, Low Profile, Floating Head, Door Catch - Medium Pull
prusaprinters

With the magnet on the tip of the rod, block all of the empty holes and installed magnets with your fingers, except for the hole in which you are inserting the magnet. Push the magnet in place, making sure that you have the magnet in the correct...

The Tekhenu lamp
prusaprinters

Also the length of the GU10 lamp has to be 53-54mm. Base top cover Neodymium Disc magnets 5mm x 1mm - 4pcs Screws for plastic 3x12 - 2pcs GU10 lampholder Base Scarab - 4pcs Cable with on/off switch Base plug Nylon cable ties - 1pc Superglue gel Sand...