flashforge creator pro e3d v6

The Creator Pro arrives with a spool holder that often proves too bulky for many spools. Several innovative designs have been proposed as solutions, but some are challenging to print, necessitate assembly, or fail to accommodate spools with...

Extra-long spool holder for Creator Pro required due to inconsistent reel sizes among filament manufacturers. A spacer clip can be used to adjust width or print multiple clips to prevent narrower reels from falling off the spool. ...Raft-free printing...

Mount E3D V6 Hotend to adapter with two M3 screws until secure. Tighten E3D Nozzle against heater block a quarter turn back. Heater module reassembly and reconnecting wires to the cutout. Plug in electronics for test purposes, power printer and warm...

To integrate the new printhead into your Leapfrog Bolt Pro, you'll need some additional parts and basic soldering skills. If you're unsure about how to proceed, feel free to leave a comment below and I'll provide guidance. ... My initial print test was...

I recently purchased a FlashForge Creator Pro2 IDEX 3D Printer, with the removable build plate option. IMHO, the removable build plate option is a required addition, as it makes print removal so much easier. The only thing I thought was missing was...

I love the variety of filament alignment brackets available here for the Flash Forge Creator Pro, but one persistent problem I encountered was that after a few prints, the filament tubes would simply drop through the holes of the alignment bracket to...

I purchased a Raspberry Pi 4b 4GB for running Octopi on my FlashForge Creator Pro. Unfortunately, I couldn't find a compatible Pi4 case for my printer, so I remixed cartermultz's Pi4B+ Hex Case with dewhisna's Pi3 Sleeve Case to create this unique...

... the back plate, plus inserted slots for securing M3 nuts on the rear bracket for a tighter grasp when assembling the parts. ... Print Settings Printer: Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.20mm Infill: 40% or greater

Here's what's changed: Duet 3, E3D V6 hotend, and a 50x15 radial blower for cooling - this baby's got some serious oomph at 3.85 CFM, and the best part? It's whisper-quiet, operating at a mere 25dbA ±10%. I've also swapped out the leveling sensor for...

... into the existing cooling fan and utilizes the same screw holds. Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: Yes Resolution: 200 Micron layers Infill: 20% Notes: Print from ABS or PETG to resist heat from the extruders.

But in this case it is adapted for Flashrorge Creator Pro: 1. Depth made less at 5-6mm to fit back decorative wall; 2. Added a hole for fitting near the screw; 3. Made bottom thicker 0.75mm for resin printing. Printed on resin phrozen mega 8k...

... bracket for better grip when connecting the parts. To print this project, you'll need a Creator Pro printer with the following settings: Rafts don't matter, supports are optional, resolution is set at 0.20mm, and infill should be 40% or greater.

This customizable bracket fits the FlashForge Creator Pro and printers with similar build plates with M3 bolts at their corners. The adjustable knob makes it is easy to swap out glass plates if you have more than one, so you can start printing on...

These files are meant for the FlashForge Creator Pro, but will probably work for similar printers with a 230x155 mm build plate as well. If you have a QIDI Tech 1, you need custom files (https://www.thingiverse.com/thing:3032840) due to the...

The versatile adapter perfectly complements the user-friendly FlashForge by providing a convenient platform for easy tool access and effortless workflow optimization.

This remix is for the Geeetech i3 pro B.

I did hot glue it in place but I am thinking of designing and printing a spacer to place between the filament guide and the inside of the Creator Pro, possibly eliminating the need for hot-glue. Printed at 40% infill and I will be adding some low...

I did hot glue it in place but I am thinking of designing and printing a spacer to place between the filament guide and the inside of the Creator Pro, possibly eliminating the need for hot-glue. ... Printed at 40% infill and I will be adding some low...

The spools of filament I purchased refused to seat properly on the standard spool holder supplied with my FlashForge printer, which boasts a 66mm x15mm spacer at its base. In stark contrast to the spools that came bundled with the FlashForge, the new...

With my Flashforge, current models didn't fit very well and required modifications to enable the Extruder idler to open freely. I also wanted to simply use the included center brace to manage cables effectively. Here's my remix. I've printed and...

This is an add-on to http://www.thingiverse.com/thing:735350, engineered to secure split loom (1/2" or stock Flashforge) covered wiring in place. The original design's small filler piece was deliberately omitted for this iteration. To ensure a flush...

If the M104 was in the start script then you would have do disable the other extruder like Egurs profile or have whole different profiles for each side like Lyl3s profile. ...So you need to make sure that you have a skirt around your print because this...

This appears to be a detailed guide for modifying an E3D hotend for use with a custom printer mount called "Overlord's Mount." The guide provides step-by-step instructions for assembling the modified hotend, which includes swapping out the stock...

Remix for Tronxy X5SA Pro: - Shifted screw hole to the left position - Eliminated material to facilitate belt insertion on the right side Cooling fan mounts seamlessly with a hot glue gun... ... Scaling may be necessary, ideally 10% (Fusion 360 appears...

... been using the 2016 edition of my multi-width bracket, and it turns out that's actually designed for the 2015 model. ...Because of the open clips on the v.2016 Creator, this bracket may not grip as securely as the one made for the 2015 version does.

... ABS (using 230C/110C heat settings for extruder/bed) Medium speed 20% infill Finally, hit print and you're ready to go! Here's a link to the Tinkercad model: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports

... following were defaults (which I kept): ABS (I use 230C/110C heat settings for extruder/bed) Medium speed 20% infill Ok, then print! Here's the Tinkercad link: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports

The photos show a comparison of my 55° mushroom test (https://www.thingiverse.com/thing:2005832) on a PLA print between this duct, the v6 dual duct, and the stock duct. The result from the stock duct looks more decent than what I expected while I...

This shim is designed for the glass products sold on this website:\nhttps://www.flashforge-eu.com/parts-and-accessories/frosted-glass-build-platform\nPrint Parameters\nMachine: \n Flashforge Creator Pro\n \n Raft Settings: \n Disabled\n \n Support...

However, this is my latest creation - a bespoke E3d V6 head design that requires some fine-tuning to get it just right. It needed some precise grinding down and fitting adjustments, plus additional holes to ensure seamless functionality. I'm...