ft 817 3d models

I'm standing near my trusty Yaesu FT-817 radio.

Stnad for yaesu FT-817 radio Category: DIY

Simpel shelf for Yaesu FT-817. ...Plase feel free to add your ovn callsign in the Scad file.

Simple shelf for the Yaesu FT-817 radio. ...Feel free to insert your own callsign in the Scada file.

The user manually configured their Yaesu FT-817 to utilize the printing capabilities of a LulzBot Mini.

Fat finger Spinner Knob for the Yaesu FT-817. ... Probably would work for most applications requiring a 26mm Knob with a 6mm Shaft.Note: Ream out the Shaft Hole for a 6mm press fit, or Ream out to 6.5mm and self-tap the original Set Screw.

Yet Another powerpole anderson adaptor for the yaesu ft-817! But i need to accomodate a standard power connector which is long. It is very robust. Additional components needed: * TS240 connector (Male DC Power Plug Connector Angle 90 degree L...

A custom cradle stand is designed to hold a Yaesu FT-817/818 securely in place. The stand consists of four distinct components. ...To assemble it, tap an M3 or #4-40 UNC thread into each hole on the two side panels and then attach the front and rear...

This upgraded Yaesu FT-817 amateur radio features a replacement knob. To install, first remove the original knob's rubber collar using an Allen wrench and unscrew its set screw. Slide the new crank knob onto the tuning shaft, secure with the set...

To power my FT-817, I designed a custom shoe that perfectly fits these packs. Creating the contacts was straightforward - simply use some #10 copper wire and flatten one end to secure it within the battery compartment. ...The shoe fits snugly but...

The angled plug is designed specifically for powering the Yaesu FT-817 and features a thumbscrew that secures it in place (remove the existing grounding screw first, located on the back of the device). A 2x0.75 mm² cable is used, but if thinner...

Simple retractable Stand for the FT-817, FT-818 Radio. ...Nut should be selfsecuring or use Locti** (no advertising)

Battery replacement cover for the Yaesu FT-817/817ND and probably the FT-818. The published part has no callsign added. ...You can add this on Tinkercad.

Yaesu FT-817/818 stand. Stand is assembled using 3mm countersunk bolts and nuts. ...I used velcro strap to hold radio to stand.

This is a shorter version of Damon's Yaesu FT-817 powerpole adapter. ... I created it to allow the use of cables with strain relief.

https://www.thingiverse.com/thing:5248147 Designed off of Geardwn's Yaesu FT-817/8 Digirig Attachment with 1//4-20 Threaded Insert. https://www.thingiverse.com/thing:5248950 This object was made in Tinkercad. ...Edit it online...

Compact Portable Radio Solution - Enhanced Functionality Elevate your mobile operations with our versatile Yaesu FT-817 radio accessory system. Engineered for convenience, this package includes essential components to boost the performance of your...

To enhance your FT-817's functionality, print a higher quality knob using your replicator. However, ensure that the model suits your updated device. Make the new knob parametric for future adjustments. After printing, remove the stock knob's rubber...

The knew knob is awesome on my radio. Print instructionsCategory: Hobby Summary I decided to print out a new higher quality knob for my FT-817 on my replicator. I soon discovered that the model used to print the knob on my cupcake didn't fit right...

Do not use the plug on the transceiver without proper crimping or complete wiring with the speaker mic, as this will inevitably cause damage to the FT-817! The electrical insulation of contacts and components is a given. When assembling all parts...

This is yet another Power Pole adaptor designed for the Yaesu FT-817(ND). It's based on Damon1974's design, but with a few key changes. One of the most noticeable updates is the addition of a standard charging/power supply plug socket in addition to...

This is a Stand for the Yaesu FT-818, FT-817, FT-817ND. The radio sits on top of the stand and is stable for shack use, your experience in the field may vary. ... 73

This design provides protection for the knobs of your Yaesu FT-817 or FT-818 radio by utilizing the stock screws without requiring adjustments to their length. You can print this stand separately, which is removable when you need to move it for...

This is the protection frame for the transceivers Yaesu FT-817 and 818. It keeps the original metallic side attachment for carrying the radio without any risks. Equipped with foldable feet for better handling and transportation. The...

This is a spacer to fit between a Yaesu FT-817 radio and a Z817 antenna tuner. It has a sound horn to direct the audio from the speaker on top of the radio forward. ...

I created a straightforward adapter to substitute or supplement a shoulder strap for an FT-817 or FT-817ND. You'll only need to purchase the strap itself, as the existing screws work perfectly well. ... Print Settings Printer: Monoprice Select Mini ...

This battery pack is specifically designed for the Yaesu FT-817, utilizing three high-capacity 18650 Li-Ion cells that are individually protected from damage. ...To get up and running, simply swap out the stock battery compartment for a custom...

Use the original screw from the FT-817/818 knob. Support required under the knob spinner. Used Prusaslicer's Paint-on Supports. ... Update: Added a new version (V3) that brings the ring closer to the center, avoiding any need for supports that...

I'm excited to showcase my first "table legs" design, carefully crafted to securely hold my Yaesu FT-817 and its paired LDG Z-817 tuner together in one neat package. With just rubber bands as a temporary holding mechanism, the LDG is perfectly...

... in the "dovetail" connectors, which are robust and aesthetically pleasing. This design might appeal to owners of the FT-817 from Yasu. ...The body is not designed for backpack use; instead, it's better suited for a more structured carrying method.