geekup bits 3d models

I used a 3.5 mm bit so that there was some adjustment slop. Loosely attach the bearing holders to the plate. Slide the rods through the bearing holders. Attach your rods to some 1-2-3 blocks on your surface plate, using your rod spacer guides to...

so this antenna holder moves the GPS antenna a little further away from the lid, as well as away from the other antenna and a bit further from the circuit board. I'm not an expert by any means, so I'll be testing this to see if it actually improves...

You wont see insane speeds on an ender 2, and an 8-Bit board will still be fine. That said, if youre doing the 24V conversion, you could also look into using an SKR v1.3 Board with TMC 2208/2209s. That would also make a very nice and silent printer,...

You will also need 4 m3 12mm long bolts and nuts to hold the cable roller and the velcro bit to the jackreel 6 13mm OD 4mm ID stainless steel bearings. (something like this should work https://www.mcmaster.com/#7804k103/=17gvmvh ) 2 sections of 16MM...

Top view error: notice the non-concentricity in the center mounting hole Front view error: mine sticks out a bit further on the ends. Future improvements: lever I can only do so much, so I settled for producing a friction version. The rear shifter I...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

For the receiver, I hear the [Nano...

You'll probably have better results ;) You'll need one Mini RC boat kit "777-218 boat", can be found on Ebay, Amazon GearBest and so on, for about 10-15$. You will also need about 15-20 grams of lead beeds or small nuts to use as ballast. Some CA...

For electronics, I used the information from this site https://alexgyver.ru/gyvermatrixbt/ and chose the simplest option. BOM (approximately $7) WS2812 LED Full Color Module 64 Bit 5050 RGB (approximately $ 4)...

The pulley/axle design was a bit problematic. Nothing was keeping the axle from sliding out of the bearings. To solve this, glue was used to attach the axle to an inner bearing race. The aluminum flat stock was chosen for the lever arm because it is...

Make sure to pull the trigger halfway or more so that the Bolstracikter (Thing that hits the bbs) is seated properly and inside its rail.You'll want to clip the 1 layer thin bit of plastic on the follower to allow the band to go through. Next you get...

Added a small rise to the lower/female lip to soften the sharp corner, and now including a PETG printer config that seems to produce good results. Update April 7, 2020: We've found that PLA seems to print a bit more air-tight than PETG, but that can...

We could see that the eyes were a bit too far apart, so we placed them slightly closer to each other. Initially, the eyes were each 0.8 cm away from the edge of the ghost, and we made them 0.85 cm away instead, which matched the original ghost far...

The "Bottom" file is a bit slanted. This is because my MicroSwiss bracket has a slant to it. Without adjusting for this slant, my shroud kept hitting the bed clips or the bed heater strain relief. For assembly, the exploded view pictures should...

Much of the process after cutting out the segments will be the same. The software I'm using to run the sceptor is available at via the online Arduino Editor here Parts LED RGB Strip - Addressable, Bare (1m) OR LED RGB Strip - Addressable, Sealed...

Also (constructive) criticism or exchange of experiences is welcome! Post-Printing Sketch für ARDUINO: int topleft; int topright; int downleft; int downright; int drehen; int heben; void setup() { pinMode(8, OUTPUT); //Heben / Senken pinMode(9,...

I then pushed it a bit farther with my fingers and then put the second bearing on top of it the same way.Then, the motor shaft could be carefully pressed in to make a rotating assembly. You might find that the shaft is a little loose or a little...

Because of this, I designed an extra stand that allows a bit of extra room for a thicker cable. You probably won't need this on your lamp, But I've included the STL for those who wish to use it. It can be glued in place or just packed out with felt...

Modify the chair a bit. See the pictures . You can make it if you have a good running setup and all parameters under control. As long as the parts are related to each outher it should work on any printer. . The first part accuracy really...

Each eye had a measurement of 7 cm but when we were on solid work we were looking for something that didn't match it with the real one so that’s how we added one more centimeter but we did it a little bit bigger than the real one.  Take the...

I added a bit of tape to hold the wires down so that they don't get tangled up in the servo lock. 16. (Don't glue the top on unless you want it to be permanent - use screws instead so that you can still have access if you ever need to fix...

Und um das Hochfahren des Scherenhubtisches zu erleichtern, 4 Zugfedern oder Gummibänder mit Kabelbindern befestigt, wie auf dem Bild, einbauen.-----------------------------------------------------------------------------------3D scanner V7 Open...

Some are full height, some are a bit lower. Buffer beam shapes seem all over the place as well… I just picked two versions that seem to be quite common. - Long hood: apart from endless variations in doors and air gratings (again, I just picked 2...

Use what you might find useful, however, I do not know if every part is fully compatible with the original set, since I have been modifying the original design of the pieces a bit to work better in my personal replica. I recommend using the hammer...

                                                                      ...

Print with hex nut holes down and slicer supports turned off Hardware required 2 - M4 Hex Nuts 2 - M4 x 20 screws 2 - M3 x 8 to mount to X Carriage Test print of Hot_End_Fan_Duct Printed in PETG 40% fill Post-Printing Clean out support material Clear...

These work a bit easier, you have to use some glue on the end of the arms where they engage each other but they do form a more substantial frame to hold everything in place. The design is such that all the electronics is upwind so the ozone, which is...

The space shuttle is fixed to the second hand with a bit of glue. Of course, other objects can also be glued to the second hand. However, it must be noted that the objects must not be too large and heavy, otherwise the second hand will...

(These are available cheaply from eBay - search for "usb c connector diy").With a long power cable length, it may drop the 5 Volt supply voltage a bit. It may still work. (I haven't tested it.)<br>I decided to use a 12V 1 Amp mains adapter and a...

- Image source [printertec](https://www.printertec.ch/elektronik/arduino/335/skr-mini-e3-v1.2-control-board-32-bit-cpu-32bit-board-fuer-ender-cr-10) - Pin for Firmware: PC14 #### BIGTREETECH SKR Mini E3 V2.x - Connect the probe to the two marked...