giant squid view in 3d

I bought the E3D V6 clone (1,75mm, 24V, Allmetal) from Trianglelab: https://www.aliexpress.com/item/32888737278.html Installation: • Install Community Firmware Alpha 4...

How I Designed This The basic points-on-a-sphere algorithm was originally from here: https://github.com/clothbot/makerbot/blob/master/fabjects/libraries/constructors/map2PointsOnSphere.scad Which was in turn derived from here:...

The Front sight has the following adjustments: I opened up the hex nut openings on the mount I also made a counter sunk recess in the bottom of the front mount to accommodate the sight The Rear sight now has (2) areas for the windage (on both sides...

Below is an Onshape link to a variety of example sleds which support nearly all extruder and hotend combinations currently in the popular market.  Example Sleds: Onshape Links: Single 5015 Throughflow Sled:...

A few things need to be in place before we get to the code: * The extruder(s) M92 value must be calibrated as best as possible * The slicer's flow rate also must be tuned. **This is important if you have to change the M92** * Firmware retraction...

 BEHOLD!!!The handle for all those people that love hidden tang design but lack tools and time to make the right fittment or that are just too damn lazy to do it themselfs (check, check, check).Sloppiness is a designer's virtue as is laziness...

Print: (1) Left (1) Right (2) Covers (2) Plugs The 20mm screw and nyloc fastens quite normally in the bottom hole. The 35mm screw screws into a hidden nyloc. This nyloc is placed into a cavity under the arm after you print. You then cover the top...

... print pauses lay the mesh on the part and hold it firmly with paper tape on the sides. Ensure that is laying in tension and adherend on the plastic part. Continue the print.DonePrint SettingsLayer height:Material: PETG

The two parts are designed to be glued together, and I plan to use Gorilla SuperGlue Clear Gel to do that (it has worked well with PLA in other projects). I have tested them and they snap on the top plate of my cubicle pretty firmly, but are easy to...

A small hole was left in the center to allow it to breath since the Abbott literature says that is needed. The template was also redone. The inside hole was enlarged slightly and it was reshaped to slow the fraying of the patches. I also needed a...

The cylinder retracts to its original position, ready for the next item.Unloading Phase:Activation: The control unit switches the solenoid valve to redirect the compressed air to the opposite side of the cylinder.Movement: The cylinder extends or...

This device covers the snout, with options to close in the front for better air quality control or leave it open to allow eating while wearing the device. Twin 1" NPT threads on either side can accommodate a range of attachments. These include: ...

Here is a TPU spacer to be used to install the really nice HEPA & Carbon Filter designed by PrinterBox [ https://www.printer-box.com/hepa-carbon-filter ] on the marvelous [Prusa] Box also from the same designer [...

Remix of a remix to fit this under counter lightbar: https://a.co/d/aLcCabf ASOKO LED Under Cabinet Lighting for Kitchen with Touch Sensor, USB Plug in Under Cabinet Lights, 12 inch Under Counter Lights for Kitchen,Daylight White 4500K, Under...

... together. The driver guards can be glued in, or held with a blob of blue-tack, there is 1mm clearance at the bottom of the socket. .f3d files are provided. Please post your makes. ... Thanks again to Hexibase for posting the acoustic design!

i can see this becoming many types of holders similar to the matco style system but most importantly are the dimensions of the pegboard which has a high resolution of holes - every 10mm this can be used for all types of drawer organization but is...

... logic the copyright does not apply, if you make it to your personalization you can if you wish apply the copyright. If you find that its physically impossible please tell me in comment, and if your explanation is satisfactory it will be deleted

The filament sensor's top section (only) from the CR10S is reused in this design. To complete it, simply insert the screws and slowly turn them with gentle pressure. Be certain to keep the screws aligned - that's all there is to it! I printed it...

I had to use fan fixing screws that are generally found in our PCs to fix the ESC support. The metal engine mount has no screws provided. I used 3 * M4 / 12 with bolts and 1 M3 * 12 To fix the batteries I use 10mm ribbons and the miniature...

Several flower pots, this time with some variations of a geometric repetition that reminds me of a mountain There are 6 differents models, each can be printed in vase mode. There is no hole at the bottom. It can be also interesting with a light...

Step file and fusion 360 file included Two sizes of rotating platforms - 80mm and 140mm in diameter For basic rotation it is possible to use something directly from the example for Arduino (part of Arduino IDE). It is also possible to add a...

So that makes it way much powerful than the commercial counterparts All you need todo is buy the following from Amazon or similar UV light source. https://www.amazon.com/gp/product/B0110LTT1I/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 I...

VIDEO: FILAMENTS: - Light glitter grey: https://www.impresoras3d.com/tradetracker/?tt=22573_12_387969_PLASmartfilGliterPlata&r=https%3A%2F%2Fwww.impresoras3d.com%2Fproducto%2Ffilamento-pla-smartfil-glitter-plata-brillo-175-mm-750g%2F - Dark glitter...

The design of the fans in the control box wasn't good enough for me, and I wanted to use a larger PC fan instead. So, I removed all the fans from the control box. Next, I took off the base plate at the bottom of the power supply, allowing the new fan...

More information on how to do this can be found in the PPP Puzzle Modeling tutorial. ### About the Designer Stewart Coffin has been called "the most outstanding designer and maker of interlocking puzzles." He is credited with over four hundred...

This part will hold the ext mosfet board, and then you just use a bit of hot glue to glue it in. The mount then goes between the edge of the motherboard with all the power connections and the side of the bottom of the case. The side already has a...

* https://onstep.groups.io/g/main/wiki/3860 BOM: * Precision geared steppers with 8 mm shaft output ** https://www.omc-stepperonline.com/nema-17-stepper-motor-l-40mm-gear-ratio-100-1-plm-series-planetary-gearbox-17hs15-1584s-plmg100 **...

... tag us on our social media page! Happy printing :) FB :https://www.facebook.com/forged.path.miniatures Instagram : https://www.instagram.com/forged.path/?hl=en If you're interested in getting our commercial license, please visit our Patreon page.

The clearances designed in should work okay on most machines with PLA. If your print will not free the jaw/teeth, increase the scale uniformly by approximately 5% as that will increase the internal spacing necessary to make the jaw move. Refer to the...

Tailfairing02 - A fairing in front of the tail landing gear. Valve01 - A butterfly valve for the supercharger intake. Tube01.STL - A tube thing for the right side of the fuselage. DFantenna01 - A direction finding antenna for under the fuselage...