header modeling blocks

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

without any 3d modeling skills. It only takes a few minutes. ---------- __Features__: --------------------- - __Standard Fan Presets or Custom Size__ (25, 30, 40, 50, 60, 70, 80, 92, 120, 140mm) - __3 Frame types__ - __Over 30 different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

InfoThe provided model is a very simple mold to cast some silicone into it. This will result into a mold itself to cast the 25% sized 3D-Benchy into resin.</p><p>Volumes to calculate the necessary amount of silicone and resin:</p><ul><li>Silicone:...

* Select the model you want to print based on your printer's nozzle diameter, paying special attention to whatever preview you have available in your slicer. You want one perimiter shell with a tiny bit of squigly filament in between shells * The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

Its a tiny model roughly based off of the Prusa Mk3s that “prints” along with your printer!While rotational movement as an indicator is fun, I thought it would make for a fun challenge to create something that converts the rotational motion of the...

After the actual print of the model has started the control switch can be quickly flipped to the Auto position to enable the auto power off of the printer at the end of the print.  If at any stage you wish to disable the auto off function, simply...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

Perhaps my specific model of the C270 camera had some differences? Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip for...

This allows protecting the model against falling over.Printing configurationLayer height 0.2mm0.4mm nozzle15% infillWhite PETG filamentplace the two halves making the bottom part of the sensor housing to their sideno support except for the top...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

I am now only weeks away from getting my own printer :) but in my preparations, i found, that i had used an inaccurate BTT filament sensor model, in my design. It was pointed out to me that i never mentioned, which panel thickness i planned...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

...March 23rd - Created a smaller prototype mockup for the bottom, mid and top tray using measurements from the full sized model. Experiencing corner lift on the middle tray, even with brims and the lid/bottom of the middle tray is about 1mm too short.

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

Although the chinese version is much cheaper, be warned that some models lack the reverse polarity protection feature from the original, even if they claim otherwise on the backside. Also, some clones have a different layout with non-centered power...

Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created and tested by Ty Mansfield, at The Tabletop Engineers.   Talarius is a melting pot...

Being in the United States, getting replacement parts for British model locomotives can be challenging, un-environmental, or impossible. but I found that the Bachmann Percy chassis shares a similar wheelbase to the 0-4-0's, and the Bachmann Duck...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

0.2mm tolerance for sliding parts Verified to Print well at 100% and 150% sizes (0.4mm nozzle, 0.2mm layer height) My Colors for each .stl model Gold - Gold Tool - Gold Diamond_T7 - Blue Bolt - White Barrel - White BarrelSpring - White BarrelPinV2 -...

Not a problem with a well-tuned MK3S+.&nbsp; &nbsp; The box was printed usingFilament &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 34 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Step 1: Use a 3D modelling program (i used Fusion 360) Step 2: Create a solid layer which is as thick as your first layer (0.2mm for example) This first layer will be the layer which touches the print bed. I used a glass bed for almost perfect...