hydroflask sleeve 3d models

DesignThis is the reduced to the max case / housing / sleeve for the Raspberry Pi Zero (2 W) in the version with cooling (we have another model that is prepared without cooling), less is hard to imagine. A foldable print in place housing with live...

  Print one of each size of sleeve and gear for the system. Use them as required, to fill the shaft between the reel and the cap (as shown in the photos).  See the notes below, for my caution about leaving a small gap under the head of the...

Now put the 3d printed sleeve in the holder, and such setup install on the bracket separating it with wide M3 washer, using 30mm screws.On the end put the M3 nuts in the recesses on both brackets tops, then screw long 40mm screws through them. They...

All Organiser versions include the ability to hold 45 Train Cars and up to 12 playing cards (fewer cards if sleeved). See explanatory computer render for identification of each of the 3 optional parts - Score Marker Holder - Station Holder -...

For most printers a 283x208mm print is too large an area to be printed in one hit (thats the interior dimensions of the box; which amazingly is what would be required to display 9x beer cards at once!), So I'll have to devise some way of printing...

Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in sleeves. - Main deck slot holds ~40 cards. - Slot for ~15 extra deck cards added below main deck. - Graveyard slot expanded and able to hold entire deck. -...

The official Sony version of this cable is called VMC-MM2, but I've only tested the third-party one.If both cameras are identical, then I found that with my Sony and Canon cameras, I could take two shutter release to phono jack cables, and join...

I also put an extra PLA nut on the lever end of the thread to prevent the ball bearing threaded PLA sleeve from moving. The expanding spool holder has an adjustment range from 50 to 60 mm in diameter and the toggle lever action alters the diameter...

If it is possible for the wires to short on the heat sink, sleeve them with a piece of insulation from the wires. Now glue it together. Making sure there is enough room for the retaining knot in the BOLT, slip the BODY into the BOLT so it finishes...

I want to mention the "Ultimate Massive Darkness 2 organizer - Sleeved Kickstarter Edition" by WingsOfDaidalos: https://www.thingiverse.com/thing:5268184 I took "massive" Inspiration from that, especially the idea, that you put all class specific...

In case the diameter is reduced at location for the harness lines, a trick is explained in part 5) : a PLA sleeve can be build to make up for the gap. 3) boom diameter at clew between 29 to 36mm. The default design was made for 35mm boom and I...

Plus there are a few novelty tricks up its sleeve: - A novel "Easy 2 Resist" resistor measurement station. Just put your standard probes into the demon's "eyes" and measure a bunch of resistors much quicker (see photos/video). It's especially useful...

The screen protector sleeve and the flexible Velcro straps are the only sewed parts. I printed all the parts out of PETG at 0.3mm layer heights.  No supports for any of the parts! I have included a short build guide in the downloads with more...

OD = 4" ID = 3.5" • 4'' Stove Pipe Sleeve - This was designed to attach to the end of a 4" stove pipe for a Thien Baffle setup. The stove pipe end is .4" long with a notch to fit around where the pipe fits together. The other end is 1.5" long with a...

As changing the extruder required some redesign, I decided to just roll up my sleeves and change everything that I didn't like from the previous design while I was at it... *** For Anycubic D 'Predator' Delta printer only. *** Designed for use...

It is designed for cards without sleeves. SITE & GUARDIAN ORGANIZER: Site and guardian tiles are kept here in 3 sections. There are indentations to facilitate the draw. Thicker walls reinforce this container. Level I, level II and guardian tiles...

This expansion sleeve slides over the "nut" and "bolt" pieces - increasing the capacity up to 85mm. Mounting Options Personally, I have an Ikea ALGOT wall shelf above my printer and I just have the 5/16" rod cantilevered out from one of the support...

Feel free to cover those wire messes up with a nice protective sleeve if you want; the connections work like regular arcade buttons so wiring shouldn't be hard. All set! Just slap that adapter on top of your stick (starting from above, slide it...

There are also holes in the top for integrated cup/pen holders with a 3D-printed translucent sleeve and light strip channel so they light up too. I used birch butcher block, which I found to be a great material for this project. I tried some dark...

Design After seeing Voultar's install video of this, I had an idea to make a housing for it myself, which was inspired by original cocktail arcade cabs. Video can be found here: https://www.youtube.com/watch?v=1AVXhiTlmgo Hardware Most the info from...

The thin sleeve from previous version 1.1 has been removed from the design. To interlock you will probably need to hammer each piece together to make them flush. In my next update I will be adding bracing for battery packs that will ensure they...

It includes 4 sleeve sizes: small, regular, large and extra large. There is also optional an adjustment strip which you can use as a wedge to fasten a buddie to a chopstick.</p><p><strong>Print Settings</strong></p><p>Always go to the above web page...

Stuff to print: - 1 Diffuser (the big star-shaped part that transfers air from the impeller into the volute) - 1 Volute (the snail-shaped thing) - 1 nozzle (straight or 90 degree, your choice) - 1 inlet bell (tall or short -- tall is best if you use...

To assemble some body elements, you need to make connections using a threaded rod and M3X8 sleeves. Installing the body on the TAMIYA DT03 chassis does not require destroying or modifying the original chassis. Only in one place you need to drill...

I tried to work as safe as possible with the mini lathe (no long sleeves, removed watch, closed safety covers, etc...) but I do realize working this close to the chuck might not be the best idea, so I wouldn't recommend you doing this. Some of...

So, regardless of your sleeving preferences, these trays should work for you. The tray also includes three peg boards, for Level, Hit Points (Wounds), and Experience. Level is capped at 9, and Hit Points and Experience at 26 - you might get more...

Video can be found here: https://youtu.be/d8us3OWgS1A More info can be found here: https://hackaday.io/project/173854-3d-printed-high-torque-servogearbox-version-2 Components used: 11 × 3D printed components Can be found on Thingiverse 1 × 775...

For Example: I used 2x 3mm² end sleeves which fits perfectly. There must fit a 3mm Screw inside that shell to fix these two gears together with fewer tolerances. Be sure the screws just fix the shell with the other two structures (cap/baseplate),...

The container is sized so that normal FFG sleeved cards can fit nicely (95mm x 67mm and 45mm x 67mm). The AT-RT container also has a small space for extra weapons, I've just glued a bit of metal in mine for my magnetized weapons to cling to. The...

Note the length and trim the extension, then solder a triple adapter on it to be able to connect it to the wire.Connect the extension with the printer wire using the 3 pin header row, then run the wire inside the sleeved cable all the way to the...