hypercube 300 3d models

These are a few accessories I remixed in Fusion360 for my Hypercube 300 (https://www.thingiverse.com/thing:2517628). They are intended to be snap fit on any 2020 extrusion. Update: 2018-11-14 I added a few accessories I use with my 2020-based...

STL's starting with HC fit the original Tech2C Hypercube and my Hypercube 300 b. STL's starting with HC300 fit the Hypercube 300 only c. STL's with no prefix can fit any printer that uses 2020 type extrusions 1/17/2018 - Updated all STL files to...

This is a complete redesign of all printer parts for my Hypercube 300 design published in 2017. https://www.thingiverse.com/thing:2517628 Everything has been redrawn from scratch to make all parts lighter, stiffer and easier to assemble...

The HyperCube 300 Lite X Carriage is a completely new X axis carriage and E3D V6 or Volcano Extruder mount for The Original Hypercube CoreXY or Hypercube 300 CoreXY 3D printers. As its name implies it is 50% lighter than the stock parts. This will...

------------------------------------------------------------------------------------------------------------------- ** Required Hardware **...

If you are building a Hypercube 300 with standard 440mm Y extrusions the included alignment tool STL will perfectly center and align the ball screw mounts and print bed in the frame. Big thanks to Lee Buxbaum on the Facebook Hypercube group for the...

Drive the Z-axis leadscrews on your Hypercube 300 with one motor and a belt with this parts set. ... You'll also need two 8-mm pillow-block bearings with setscrews, two 8-mm-bore GT2 pulleys, a 5-mm-bore GT2 pulley, a couple of 3-mm-bore GT2 smooth...

I wanted to use a Teflon sleeve with the Hypercube 300 X axis. The carbon rods I am using are not 100% even across and are binding with the original PLA bushing. It will fit the IGUS 10mm bush sleeve. There is a 0.6mm lip on the inside to prevent...

These are Hypercube 300 frame assembly tools. Update: Now all printable on a 200x200mm printer! The Frame Assembly Tool is for making the corners square and setting the parallel Y extrusions on the left and right sides of the frame. The Z...

One of the design goals for the Hypercube 300 is to keep the mass of the CoreXY mechanism down so it can run faster; this is why it uses things like carbon-fiber rods on the carriage axis. The XY joiners of the original design call for LM8LUU linear...

The BLTouch in my Hypercube 300 is acting up. :-( I was able to get it running enough to print this by homing the printer on X and Y, centering the carriage, rolling the bed up until a piece of paper between the bed and nozzle started to drag, and...

###Hypercube Reworked Z axis What is it? --------------------- In order to keep the original build height on my [horizontal X axis conversion](https://www.thingiverse.com/thing:3201330) I had several options. * Increase the bed height relative to...

HyperCube Evolution 300 Remix Working Size: 300x300x350 Remix: - Replace brass insert nut by normal nut - Add more clamp for X carriage and Z bearing LM12LUU holder - Remix X carriage for Inductive Sensor 18mm - Implement Spool, LCD RepRapDiscount...

<p>This started as two chains connected from the X carriage through an XY joiner to a frame mount, but then I realized that by rotating the chain 90° so that it flexes in the same plane as the CoreXY mechanism, the entire area can be covered by one...

This started as two chains connected from the X carriage through an XY joiner to a frame mount, but then I realized that by rotating the chain 90° so that it flexes in the same plane as the CoreXY mechanism, the entire area can be covered by one...

Fan Duct for Hypercube 3D - Adrian Martinez (adrianm1972)

For the frame, I used the calculations from http://superjamie.github.io/hypercube/ which gave me the following dimensions: The heatbed I ordered is this one:...

This is an X carriage that enables users to mount a standard E3D V6 to a HyperCube 300 v2 or 235 v2.

Aug-21-2021: Added z-axis-align-300 for the Hypercube 300 V1. It needed to be a little thicker. ================================================================= https://www.thingiverse.com/thing:4441076 Simple leadscrew holder to provide...

So added 20mm to the height and made the hole 9mm instead of 8mm as the bearing holds the rod. Aug-21-2021: Added z-axis-align-300 for the Hypercube 300 V1. ...It needed to be a little thicker.</p>...

......:) I remixed the carrier for the original Hypercube and the XY joiners from the Hypercube 300 to take an X axis MGN12 rail. Included are x carriers with and without an x endstop. I've added small slots to grip the teeth of the belt so it can't slip.

... laid over one another (mounting holes are also not lining up properly). This is why I quickly scetched this one on top of the z-axis mount of the hypercube 300. UPDATE 15.12.2019: Adjusted the tolerances. ...Gave the coupler a little more space.

This is the controller box for Hypercube 300/235 v2.0 printer! This works will all controllers from the MKS GenL 8 bit to the SRK 1.3, 1.4, 1.4 Turbo and the new SKR 2.0 32 bit (Duet enclosure is in progress). I left extra room for power off...

This is a Hypercube 300 redesign, using 3 leadscrews and 2 (or 4) support rods. It eliminates the center side extrusions and long rod support arms, and moves the rods to the back [and front] on the outside corners instead. May 9 - Redesigned the...

... single-piezo board, I'll make a mount for that one soon. The rest of the pieces are the same, so you can get the belt clamp for the carrier from Hypercube 300 Lite X Carriage, and the other part of the Piezo Clamp from Piezo20 Hotend Z Probe.

hi and thanks for stopping by. this is my pride and joy of the tool changer and a give back to the community where i have been following. the frame is from a standard hc300 where i have totally redesign the x and y, and is using the dual z from...

Alle Teile sind neu gezeichnet in Anlehnung an den bekannten Hypercube, aber maximal Massiv und die Z Aufnahme ist quasi einteilig. Die BOM kann weitesgehend vom Original übernommen werden. Lediglich die X Wellen sind in 10mm und nicht wie im...

I've removed some components off the bracket I didn't feel I needed for what I wanted to do with my Hypercube. This is still in a stage of creation, and I'm currently waiting for a 500mm rail (the 450mm rail I ordered wasn't quite large enough)...

Same as the original with some filament removed.

I recently ordered a volcano hotend but the sensor isn't going down enough to sense the heatbed before the nozzle touches, so I made this thing based on the original sensor mount provided by Adrian Martinez @ https://www.thingiverse.com/thing:2517628...