ide to compactflash adapter 3d models
2099977 3d models found related to ide to compactflash adapter.cults3d
Today I wanted to install a CF card and a cheap adapter to IDE into an old laptop as a hard drive replacement, but it was impossible to get it into position as it's original hard drive slides into a hole and makes electrical contact in the deepest...
thingiverse
Today I wanted to install a CF card and a cheap adapter to IDE into an old laptop as a hard drive replacement, but it was impossible to get it into position as it's original hard drive slides into a hole and makes electrical contact in the deepest...
thingiverse
Recently I have been using an SD to IDE converter purchased off of amazon in my retro Windows 98 PC https://www.amazon.com/SDHC-40Pin-Adapter-Memory-Drive/dp/B08SK28S2Y/. However the manufacturer only provides a bare PCB with no enclosure to allow it...
thingiverse
This is a drive bay cover for a HXSP-2108P IDE to CF adapter. It allows insertion and removal of the CF Card from the front of the machine. I have provided both the STLs and the Source files which were created in 123D. The board I used in the...
cults3d
This is a drive bay cover for a HXSP-2108P IDE to CF adapter. It allows insertion and removal of the CF Card from the front of the machine. I have provided both the STLs and the Source files which were created in 123D. The board I used in the...
thingiverse
This is a remix to shorten up the mount a bit, and raise the cf card up off the floor on some standoffs. ...This also as a an overhang to keep the molex to berg cabling in check.
thingiverse
Adapter sled for IDE to SD card adapter for a Macintosh Performa models using the Performa/Quadra 630 case.
thingiverse
This is an adapter faceplate for the GINTOOYUN IDE to SD card where a CD/DVD-ROM drive would go
thingiverse
This device allows you to mount the cheap and common sd to ide adapter pcb to the built in hdd slot on a beige MAC G3.
thingiverse
This is a CF card to IDE port adapter bracket which can be used i.e. ...in the Amiga 600/1200 and protects the Amiga motherboard.
thingiverse
3.5" bay for the compact flash to IDE adapters. This one should work splendidly for Amiga 1200 Towers or Amiga 4000. Instructions Made in SketchUp - skp-file included. ... Fasten the adapter to the...
thingiverse
Internal mount for IDE To SD adapter with front cover. This version is for a 3.5" drive bay. ... Required: (x8) M3x5 mm screws ----- The 5.25" drive bay version is available at: https://www.thingiverse.com/thing:5642192 -----
thingiverse
This is a bracket to install a CF->IDE adapter in an internal 3.5" hard drive bay. I collect arcade games, some of which have hard drives. Whenever possible, I replace the hard drives with a modern solid state drive (CF, SD, etc). If possible, I...
thingiverse
(so here we are) Adapter Used for this design: (Available on Amazon - See Pic) Manufacturer: Mustpoint Desc: SD SDHC MMC to 3.5" 40Pin Male IDE Adapter Card Big PCB SD-3.5 IDE PC Board Labeled: SD35VC0 Dimensions: 80.2mm * 70.2mm Design can easily...
thingiverse
...... With this you can install 40-Pin IDE To SD adapter to PCI/ISA bracket. It is easy to transfer files to SD card now, without opening computer's case. I use this with my retro-pc (Dos/Win98). Adapter is common and cheap, and it can be found from e.g.
thingiverse
This is my version of a 2.5" drive adapter to use the common, cheap 44-pin IDE to msata converters. Great way to install mSATA SSDs into older laptops. See photos for the mSATA converter this is designed for - these are the cheapest of these...
thingiverse
This is a small mounting bracket for [this IDE to SD card adapter](https://www.amazon.com/gp/product/B00DGNYXQ0/), to allow it to be mounted in place of a 2.5" drive (10mm high). Photos show it installed in a PowerBook G3. The bracket includes two...
thingiverse
A "H" structure, which allow the internal IDE harddrive from an Archos to be replaced by a IDE to SD Card adapter. As the whole Archos structure is screw on the harddrive, I needed to make a quick design. This is for Archos recoder v1, but from...
thingiverse
Its purpose is to keep the adapter in place during shipping, and to act as a protective barrier against accidental shorting of the MOLEX input solder points on the back of the board. Designed to fit the cheap (less than $4) Chinese adapters you can...
thingiverse
... Any M3 screws will tap themselves in the holes. Search "IDE SD" on amazon and you should find a comparable adapter to original product photo above. I did not print the "inverted" version, so let me know if my measurements work or not. ...
prusaprinters
The power wires still exit on the front. Any M3 screws will tap themselves in the holes. Search "IDE SD" on amazon and you should find a comparable adapter to original product photo above. I did not print the "inverted" version, so let me know if my...
thingiverse
I made a spacer for a SATA to IDE adapter to be used in the original xbox. ...This is ongoing project so there may be changes.
thingiverse
simple protector plate for a Sata-IDE adapter to protect against short circuit on the harddrive it self. I printed this in ABS to be sure it will last because of potential heat. ...
thingiverse
This works great if you're using SATA drives in a SATA system, but it can be problematic if you're trying to adapt a SATA drive for use in an old PATA/IDE system. This adapter sets the 2.5" drive back far enough that you can fit a SATA-PATA adapter...
thingiverse
... cover. Required: (x8) M3x5 mm screws for single IDE To SD adapter (x12) M3x5 mm screws for dual IDE To SD adapters Optional: IDE extension cable ----- The 3.5" drive bay version is available at: https://www.thingiverse.com/thing:5642213 -----
thingiverse
ORIGINAL SUMMARY [I didn't designed this Thing, I ONLY corrected the error from the STL file] ORIGINAL CREATOR: https://www.thingiverse.com/dogp/designs This is a bracket to install a CF->IDE adapter in an internal 3.5" hard drive bay. I collect...
thingiverse
... may need to be glued down to the PCB to minimize light leakage between the LED holes. The floppy style power connector is blocked, so you will have to use the Molex connector next to it to power the adapter. ... FreeCAD files are included.
thingiverse
Remixed from "PCI / ISA Slot Bracket for IDE 40pin to SD adapter", this adds the following enhancements: - Thicker triangle areas along the bracket so stress from inserting/removing the SD card doesn't flex the bracket as much. - Enclosed bracket...