iris model

I should snuggly fit with this model: https://www.printables.com/model/123074-ceiling-camera-mount-2-axis.03: Added the grow lights for indoor plants, see pictures. Also added a section describing the little differences. Earth anchor is good to go...

This model IS NOT HOLLOW, but is mild steel. you'll want a really long carbide bit. It drills pretty easily though, and will not affect structure. . Drill a similar sized hole on the back side of the frame. Screw the slipring adaptor into the center...

The only models where the current orientation is not necessarily the recommended one are: Duct, DripVat & Bottle Some files are available with supports. I cannot guarantee in any way that these supports will be strong enough for your printer to...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

 If you also made this mistake (or if you like the look of the colour-matched annotation labels), I have uploaded those “caps” in the model file “Fix for Rotated Board.zip”Print each label with the dimensions 185mm x 12mm x 4.78mm. (You may need...

Help others find the design.Max FOV DesignMeticulously modeled a 3D representation of the camera's field-of-view. Now the mount allows maximum TPU protection in front of the lens while perfectly avoiding being visible. Even with ND filters.. and even...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

Design Notes: All holes are designed on size, so for example a 4mm hole is modeled as 4mm. This makes it easy for me to make both a clearance hole and a hole to thread into since all of my hole always come out a fair bit small. I use a cheap set of...

The VR Box comes with pads that may fit your need here. Even if my model provided screw holes and additional holes to fit the screwdriver through, I do not recommend using them. The pillars the screws were originally drilled in are most likely...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

To do this, I will add the foot models in STEP format, they are easy to edit. Assembly video: https://www.youtube.com/watch?v=zzjLTr3RoPg https://www.youtube.com/watch?v=Tg764du-zTU https://www.youtube.com/watch?v=Vcvz-GSpdps With a 3S...

# Supplies you need to buy: 1 Logitech M510 Mouse (this model exactly) https://amz.run/67er 2 Philmore push button switches https://tinyurl.com/mr42ce4n Solder (lead is easier to work with) https://amz.run/67nL Wire https://amz.run/67f4 Super...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

* Once assembled my new FelFil extruder (https://cults3d.com/en/3d-model/tool/felfil-evo-extruder-case) I began to design a cheap and affordable spool winder; I had to design a cooler for extruded filament and a digital sensor for filament diameter.

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

Changelog: Update 2021-03-01: Steve (faultedlogic) made a remix for current A8 models with plastic bearing blocks. Update 4 (2018-06-17): added countersunk hole for chain fence Update 3 (2018-06-11): updated left motor mounts for different type of...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

 Note, only model files (.AMF) are uploaded, no g-code uploaded for the upgrade.This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

- SD socket is a twin model for normal and micro SD cards, slightly bigger opening will be necessary. https://www.aliexpress.com/item/1557385706.html spm=a2g0s.9042311.0.0.94774c4dNZcdtH - Firmware is modified to handle changes, using Roger...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

Bill of Materials ================= 1x Arduino Mega or clone (actually an Uno would suffice for the current version, but wouldn't leave much room for future improvements, and besides, I already had the Mega ;-)) 1x 20x4 LCD module (HD44870/SC2004)...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...