lithium 3d model

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

... control the LEDS with preset printer events such as warming, printing progress, error, cooling, etc. https://plugins.octoprint.org/plugins/wled/ Original design remixed from K2DesignLab: https://www.printables.com/model/174959-makerdeck-logo

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

... I repaired the model and added a cover plate that screws over the motor plate to quiet it down. - Updated 6/2/2021 I reuploaded everything, Something got messed up and a few files where missing. This includes a camera mount arm I made as well.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

is ASVFSVF14K203 [US] [CA].----------------PrintingThe “ALL.stl” file prints the entire set of models you'd need to assemble ONE power plug housing. Separate STL file for each of the part is also provided for your...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...

Related models: Track connectors for wooden railway to Plarail (and other systems) https://www.thingiverse.com/thing:5024058 Various other items of rolling stock: https://www.thingiverse.com/densha/designs Note that many 0-gauge (O-gauge, 32mm...

I can upload the design files for the other models too if there is interest. Please share your creations if you remix. : ) Update 7/16/2020 - The original inner joiner STL was undersized. I have added a new STL ("hexcell_joiner_inner_FIXED.stl")...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

This sword model is a more realistic redesign of the Master Sword from The Legend Of Zelda game series. The text on the front of the blade translated from Hylian says, "The Sword of the Hero of Legend" and on the back, "The Blade of Evil's Bane." ...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

&nbsp;I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers.&nbsp;UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table. &nbsp;I decided to make a second unit to move...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

It's corrected in the download-model.I know, this LCD knob is completely over-engineered and basically totally nonsense. But it was fun to design it and bring it to work for the LCD knobs contest.Triggered by verny's Cardan Joint Knob I thought I...

* Select the model you want to print based on your printer's nozzle diameter, paying special attention to whatever preview you have available in your slicer. You want one perimiter shell with a tiny bit of squigly filament in between shells * The...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

We'll be using a simple character model for this exercise, so go ahead and import it into your scene. You can find the model in the "Models" folder of your project. Once you've imported the model, select it and go to Edit > Object > Group. Name the...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

Both versions comes with an extra split in half model, depending on your print preferences. If you glue a cow to the ground plate as prop, remember to place it where the UFO won't crash on it's head…</p><p>&nbsp;</p><p><strong>My UFO doesn't crash...