m180 3d models
167 3d models found related to m180.thingiverse
This is a redesigned M180 carriage which will take 24mm linear bearings, instead of the 17mm bearings supplied by Malayan.
thingiverse
Malyan M180 Extruder Mount. I have also included a extruder mount that will support 24mm Linear Bearings. ...How I Designed This Sketchup 2016
prusaprinters
Malyan M180 Extruder Mount. I have also included a extruder mount that will support 24mm Linear Bearings. How I Designed This Sketchup 2016 Category: 3D Printer Parts
thingiverse
... of material. Obviously you print the round flat side down. Print Settings Printer: Malyan M180 Supports: No Resolution: 0.2mm Infill: 25% Notes: I used PLA, but should work fine with ABS. ...How I Designed This I used Solidworks and Simplify3D.
thingiverse
My work picked up a Malyan M180 and the spool holders were not big enough around. I designed these to fit the spools I use but being the same height as the originals and designed to used the bearings from the original holders. ...Added a 58 mm version
thingiverse
... screw thread. Print Settings Printer: Malyan M180 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: Printed in Esun purple ABS using blue painters tape on bed. Extruders 230deg, bed 110deg. ...Layer height 0.2mm, 20% infill, supports.
thingiverse
... material. I also included DXF files for those people with access to a laser cutter. Any questions, feel free to message me. Otherwise, Enjoy guys! Print Settings Printer: Malyan M180 Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Laser Cut
thingiverse
This is my MK3 carriage for a single extruder for the Malayan M180. I removed the left hand extruder, except for the fan, and thirmister (for some reason it will not work if you remove this) and used the right hand heating block and the filament...
myminifactory
My attempt at modernizing the Malyan M180. ... Goals:Reduce weight on gantry.Modernize electronicsprint flexible filamentsGeneral usability, easy to load extruders, usb port up front, wifi probablyrework spool holders for new extruder location ...
thingiverse
I started up my new Malyan M180, and the first problem I ran into was when I was about to feed filament. I just couldn’t get it into the extruder. The feeding mechanism could only be behind the fan. I started to dismount it with the result that I...
thingiverse
pipe guide for diameter 4 mm ptfe guide to fixe with electric cable on the back of malyan M180 i've change the extruders entry by http://www.ebay.fr/itm/281805603531?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT and PTFE pipe by a 4mm...
thingiverse
Courtesy of http://3dprinter.org.ua/ , New Pla blower for malyan M180 or Freesculpt EX2 - V2, with optimized airflow and new circular air outlet. ...Note :Pictures on the thing are wrong, and come from an older version Works with 2X 40mm 12V ( not...
thingiverse
This gauge help me to tune the nozzle height on my M180, the hotends can't rotate during the adjustment. ...You need some a solid gauge to put under the nozzles, for my settings I used a 3mm gauge between the level gauge and the nozzle (in red on the...
thingiverse
... in other direction and resulution will make them even more strong, after that I put it together with glue. Print Settings Printer: Malyan M180 Rafts: No Supports: Yes Resolution: 0,2 mm Infill: ~15% Notes: using Makerware 3.9 and SketchUp 2016.
thingiverse
I am still struggling with finding/designing the perfect fan "inlet" for my Malyan M180... I still think my low bed temps are partially because of the fans creating turbulence and cooling down the bed... ...thats how I try to prevent it without...
thingiverse
This is an adapter for your Filament spool holders on the Malyan M180, will work with others with same design of course. Made to fit ESUN Filament from hobbyking and another ebay one, anything in the range of 46mm to 65mm inside diameter rolls. Yes...
thingiverse
... exactly the same. Print Settings Printer: Malyan M180 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: Printed in Esun black ABS using blue painters tape on bed. Extruders 230deg, bed 110deg. ...Layer height 0.2mm, 20% infill, supports.
thingiverse
... is exactly the same. Print Settings Printer: Malyan M180 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Notes: Printed in Esun black ABS using blue painters tape on bed. Extruders 230deg, bed 110deg. ...Layer height 0.2mm, 20% infill, supports.
thingiverse
Improved leg pad for Malyan M180 / Freesculpt EX1 - EX2 2 versions with/out screw pad
thingiverse
Replacement part for Malyan M180 / Freesculpt EX2 Plastic part for rods anchors who tends to break Credits Goes to 3D-P.ua !
thingiverse
From an ukrainian idea ( 3D-P ) i release the filament funnel guide for Malyan M180 / Freesculpt EX2 . ... Not tested yet, more pictures to come
thingiverse
... camera mount for the Malyan m180 that holds 2 Webcams Model WC04. ...total cost at the time of making was 19$ for 2 cams and filament.. https://youtu.be/vJ2P3UX0p3Q Print Settings Printer: Malyan m180 Rafts: No Supports: No Resolution: .2 Infill: 10%
thingiverse
... Print Settings Printer: Malyan M180 Rafts: No Supports: No Resolution: Grid 0,2mm; Logo 0,1mm Infill: Grid 15%; Logo 20% (hexagonal) Notes: I had quality problems by printing it in one part, and also with the hexagonal structure in my version 1...
thingiverse
... the nema motor reduce by 2 the noise of this printer, i'm considering changing all the motor on this printer.... with stronger one ! Print Settings Printer: Malayan M180 Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 0.2 0.3 Infill: 70%
thingiverse
... designed so that the nut sits higher than the knob so that when you tightening/loosening it, it doesn't rub against the paper backing of the heated plate. Print Settings Printer: Malyan M180 Rafts: No Supports: No Resolution: 100 Micron Infill: 20%
thingiverse
This X-carriage for the M180 was designed to make it possible to use the Flexion double extruder without having to make changes to the original X-carriage. There are 2 versions one for 17 mm radial bearings, that's on the printer, and one for 24 mm...
thingiverse
Print Settings Printer: Malyan M180 Rafts: Yes Supports: Yes Resolution: 0.1mm Infill: 20% Notes: Print with the air duct pointing up and to the left - print the long extruder mounting bracket in the air with supports...the air duct and fan bracket...
thingiverse
Alors j'ai créé un modèle pour mon imprimante Malyan M180 en tenant avec une inclinaison d'un bras pour un meilleur maintien du support. Le 2ème fichier « stl » est le même que le 1er mais avec un arrondit des bords extérieurs pour ceux à qui...
thingiverse
This is a part to mount both a GoPro and a C170 / C270 at the same time to the Malyan M180 29.10.2016: ToDoList rotate the GoPro Mount by 180° or you have to use (works) the plastic as the nut :) make the C170 mount "longer" so it does not appear in...
thingiverse
... existing filament and pass the end through the brace and into the extruder tube The brace is not symmetrical - the smaller indentation faces toward the motor. Print Settings Printer: Malyan M180 Rafts: No Supports: No Resolution: 0.3 Infill: 100%