maker faire robot 3d models

It doesn't change the final file size, gets rid of component scaling issues, zoomed edges disappearing, and everyone's favorite error drawing a small circle with too many faces... The model units are set to meters instead of milimeters, just make...

For comparison sake I do get wrist cramping and hand numbness fairly quickly with the stock OGS, a Nintendo Switch, or 3DS XL. I've played several marathon sessions of Castlevania: Harmony of Dissonance for 2+ hours using this grip, and anyone...

It is a printed 1/4"-20 standard tripod thread. When I printed the original I found that the rear case was a fairly loose fit for me so I added 0.1mm thickness to the rim in the rear panel to make the fit tighter. Your mileage may vary depending on...

Choose a nice, reasonable, steady pace for good results. The sun ray (print 5 of them!) can print without skirts should you have decent adhesion and keep the speed fairly low to avoid intense vibration. I used 2 shells, 0% infill, and 5 top layers to...

3 variantes sont proposées pour les faces latérales : - Pas de logo - Logo "cube" d'Anycubic - Mon logo perso (R7) Il est bien sûr possible de combiner différentes parties avant et arrière, et je peux éventuellement faire une version custom sur...

### Code Writing the code for the Arduino is fairly straightforward. There are some guides out there. There are two options here: - If you are happy to write your own [using MHeironimus'...

---------------------- As I was intending to produce timelapses of interesting 3D prints, I realised fairly early that I'd need a way of lighting up the printer for the duration of the print. I already have an assortment of LED "video lights" that I...

This was also a fairly expensive project as far as DIY goes if you don't already have the parts. I'll put a list at the bottom of all the stuff I bought for it. Unlike some of you, I did not have a large selection of parts lying around when I...

After printing, if the parts snap together fairly easily (but not loose), then you know you've got a good calibration. If it isn't a good fit, experiment with the setting called Horizontal Expansion in Cura or XY Expansion in Prusa Slicer and print...

You can get some from Kamami: https://kamami.pl/en/goldpin-connectors/1178405-goldpin-czarny-1x40-listwa-kolkowa-pietrowa-raster-254mm.html , https://kamami.pl/en/goldpin-connectors/565044-goldpin-black-1x20-pin-header-2-54mm-pitch.html , TME:...

The tolerances in this project are quite lenient, but major flaws might still affect the tolerances negatively______________________________________________________________________________________Videos and assembly instructions:Instructions are...

You have to shake fairly hard to get the cards to come out without using the ejectors.Several holders use magnets. Right beside cards that have magnetic strips on them.No magnets here, just plastic and a few bolts.I'm not saying my design is the best...

This version is fairly similar to the original with some minor changes: 1) The user-side grille into the filter chamber has been reworked with a louvered approach. This increases air flow in and out of the chamber by roughly 100% while providing the...

The result is my Self-watering Juice Bottle Planter, designed with parameters and smart prototyping in mind.The bottle cap is fairly simple, and should fit most large bottles just fine. Of course, you could also simply poke a bunch of holes in the...

I printed on an Ender 3 v2 with cheap filament from Micro Center so it doesn't require high end stuff, but it does require a fairly well calibrated printer to ensure everything is the right size so make sure your steps/mm are calibrated for X, Y, Z,...

Due to the sideways mount of the extruder stepper motor I will have to design a new angled 4010 duct to make sure it clears the stepper and allows room for cables. I do not use levelling sensors but there are other variations which you may want to...

I found it most effective to pop the build plate in the freezer for a bit!AssemblyInsert the ball bearing before closing the two halves!Clean up the pieces - remove any stringing, sand if desired - you may want to lightly sand the corners of the...

Jake was put in the Speedville Timeout Center and the race was rescheduled so that Zorvath could fix his favorite hot rod and the race can be fair. ...Zorvath kept his shop running and kept racing and lived happily ever after in the happy city of...

Delete it before printing or your portal will have a slot in it.Book:General: There is a short version of the book cover and pages, that is what's shown in the video, and fits fairly well within the portal opening, but does look disproportionate when...

Fairly straightforward.There is a version provided that has an integrated platter. I would recommend using polycarbonate for this version because of the extremely similar properties to acrylic. It probably doesn't fit on your machine, and I figure...

I've also had a Hypercube build in the works for a while now, so I just raided what I needed from that.)I printed the plastic bits in eSun solid-purple PETG: https://amzn.to/3cndPrqSome signficant differences between the stock A8 (or AM8) and...

... print.14. - Happy printing with easy re-calibrations.The B version assembly is fairly similar. ...Only the calibration bolt position is reversed and it can also accomodate M3x25 bolt instead of the M3x30. Let me know how do these parts work for you.

FAIR WARNING: this may make you want to support the 2nd Amendment and drink whiskey from dirty glasses. When it comes to dimensional accuracy, I don't promise anything! I'm literally eyeballing everything for proportions, starting with the fact...

I've found the supports to be fairly easy to remove when printed in either PLA or PETG, with PETG being slightly more difficult. ##Hub Assembly 1. Start by pressing a 608 bearing into one hub piece, then press another hub piece onto it making...

Print slow so it will be fairly smooth. I printed at .2 resolution, but can go smaller layers if desired. The box portion has been sliced already in Cura to only have support where the cables go through. Load up the GCODE and print as is. The STL...

For the Z axis, I don't think it matters.I waved the chain around and worked the links till they were fairly loose before install. I also advise swapping links in and out if necessary, you can use the bend restricting ones with the others as long as...

I kept the flippers fairly stylized with a thicker body attachment so that they would print very easily and help support the outer edges of the body. Finally, I added some subtle musculature right behind the flippers to give the entire tail a bit...

The red/pink bits are a glued-patch due to my printer stopping 8mm before finishing that part :( If you look closely, you'll see a fair amount of hot-glue to reinforce the part to minimize wobble. Which is not too bad, with the clamp near the bottom...

Please let me know !Specifications :Fast access to the hotend and easy demount - with this montage only one screw has to be removed to access the hotend.Good cooling - it offers quite the same performances as the famous petsfang, and is far better...

The outer rings are fairly loose, i.e. are meant to be taken out and in. Contents from outer to inner ring: TEN COMMANDMENTS AND PRINCIPLES OF 3D PRINTING Calibrate well for the first layer Keep an open mind, be creative. Create supportless models...