makerbot extruder 3d models

This part holds the extruder tubing from going into the extruder feeder causing a 'filament slip.' I made the dimensions for the makerbot experimental extruder, but I image it should fit the any makerbot extruder. Attach the small end to the...

This is a conversion I did for the MakerBot replicator 2 extruder. ...I was having problems with the standard extruder feeding system so I purchased a Bulldog extruder and then I designed and machined a mounting plate, and eh presto I now have no...

... Instructions Skeinforge with your favorite settings (warning: it may tickle bugs in skeinforge. Try the gcode if the clip-on part is only perimeter and no shells). Print and clean Clip onto your makerbot and attach the cable.

... makerbot to keep the cat5e cable from dropping onto the Z-Belt. ... Instructions You probably need to file this down a bit. I leave it as it is, as the wood for makerbots has probably different sizes.

I can never find models or dimensions for these parts, so I'm putting them up as I get them. ... Makerbot's drive gear. Mounts to a 5mm shaft with a set screw. ...The inner curve is knurled.

http://www.youtube.com/watch?v=021bGXrXBPY this shows a maker bot extruder on a bfb tool because of how easy it is to get parts and nozzles in the usa. i also created an adapter bracket that holds the top of the ptfe in place when clamped by the...

Recently I noticed my Replicator 2 was not feeding the filament properly even with the "free" Makerbot extruder upgrade. I performed the pinch test as the filament was feeding through and noticed that I was able to stop the filament from feeding. So...

Customized version of http://www.thingiverse.com/thing:551484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=551484 Instructions Using the following options:...

This is a conversion I did for the MakerBot replicator 2 extruder. ...I was having problems with the standard extruder feeding system so I purchased a Bulldog extruder and then I designed and machined a mounting plate, and eh presto I now have no...

[180mm needs to be resized to 180mm ] Holds All Makerbot Method Extruders [. I don’t know about the LABS Extruder ] I ordered it and it is on its way. Neodymium magnets are added to keep the Extruder in place, either horizontally or vertically. The...

Heavily based on makedave's design. Edit 10/2/14: Button positioning moved 3mm to the right after test fit. Changes: -Spacing for body made 1mm wider to fit stepper motor. -Lower left wall on body removed (couldn't see a reason for it). -Arm...

Scanned with the MakerBot Digitizer Desktop 3D Scanner

3d printed out of pla on makerbot method x

http://www.thingiverse.com/apps/customizer/run?thing_id=189264 Instructions Using the following options: itemsShown = both boxLength = 135 boxWidth = 72 wallThickness = 3 textSize = 9 text = Smart Extruder+ topClearance = 0.2 textThickness = 2...

Makerbot Replicator Extruder Carriage for Dual Extruders

Instructions Laser cut from 3mm plywood (or probably better if you truly plan to use a Makerbot extruder, from 1/16" stainless steel). Installation is a bit tricky: First mount the aluminum block to the adapter by sliding it in through the slot and...

An adapter for the Makerbot Mk5 extruder for a stepper motor Instructions This uses a modified version of Wade's gears derived from Nicolas's http://www.thingiverse.com/thing:4305 Build the adapter part and one each of the gears. Drill out the holes...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Yes Resolution: 0.1 - 0.15mm Infill: 15% Notes: Print "...Top6" with support and "...Buttom6/7" without support. You have to turn 'em a bit. Check the...

Replacement fan duct for the smart extruder+ I printed it in PETG with no support inside the air duct There is a version with support structure as part of the model that can be snapped off after printing if you can't add custom support to your print

Helps hold the smart extruder+ together when it's taken apart, and to get the tolerances right. For what it's worth, I also made it so the pins are accessible on the back. Has holes in the back for 4 max 5mm diameter magnets if you want magnetic...

This thing allows you to mount a Makerbot direct drive extruder clone onto a prusa i3 x carriage sideways so you do not lose as much Y print area. Use the 4 holes to run screws into the back of your stepper motor (you will need slightly longer screws...

This thing allows you to mount a Makerbot direct drive extruder clone onto a prusa i3 x carriage sideways so you do not lose as much Y print area. Use the 4 holes to run screws into the back of your stepper motor (you will need slightly longer screws...

Here are IGES and STL files of the parts I have measured and modeled to represent the parts that make up a Flashforge Creator-X extruder assembly. ... I will work on getting the actual extruder modeled soon.

I printed one of Daduck748 to try to stop the printer from triggering extruder change when I was removing the glob of filament from the nozzle. It didn't fit quite right so I remixed it to have the clips in the right locations for both the non-plus...

Makerbot Replicator 2 Extruder Update with integrated dustfilter Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: No Resolution: 0,1 Infill: 10

... clip the plastic tab into the guide as not to lose it. I will be updating it over time, feedback welcome :) Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: Yes Supports: Yes Resolution: 150 micron Infill: 100%

Redesigned extruder block with smaller drive gear hole (11.8 instead of 13 mm) -> longer filament support between the drive gear and hot end so flexible filament does not get stuck in between. As CTC that I own is an Makerbot Replicator 1 (dual)...

Update 01.04.2015: Changed hole diameter to 11.8 so it does not need sanding, moved filament hole a bit, made a bigger diameter hole on the bottom so it does not touch the gear fastening screw Update 31.03.2016: as no changes have been made for a...

It also improves filament routing, material loading and performnace with others filaments You need a base parts from the original extruder, and also a parts to assemble the kit: - 1 x screw M3x10 - 1 x screw M4x10 - 1 x nut M4 - 1 x nut M3 The M3...

Used to attach the Palette2 outgoing tube to the Makerbot Smart Extruder+. ...The outgoing tube snaps into the small end of this part and then can be easily slipped onto the input of the Makerbot Smart Extruder+.