map marker 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches to...

... with the not dampened stepper motor. Ein von Martin Majewski (@martinjmajewski) gepostetes Video am 5. Nov 2016 um 4:50 Uhr Update 3: I removed the V1 models as they seemed to have some issues. ... V2 is the most current and best working version.

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

So I grabbed [YucA305](https://www.thingiverse.com/yuca305/designs)'s [Drag_Chain_YZ_Slipon.stl](https://www.thingiverse.com/thing:4648673), put it into SketchUp Online, used the STL as a mask for sizes and alignment, simplified the model a bit and...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

... Print Settings: Printer: Fused Deposition Modeling (FDM) Layer Height: 0.1mm Infill Density: 30% Support Material: Hatchbox PLA Post-Printing Instructions: Mirror Testing: Position the tester near the radius of curvature of the mirror to be tested.

Then, I saw it mentioned by a popular modeller on his YouTube channel, and over the next year, the number of downloads went up enormously. So, it seems like it's time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. There are two hull versions. The longer version (lv) is the one shown in the picture and video. But...

I thought about being edgy and calling this v6.66 but I figured a name change would provide a clean slate for the community to build from.Starting with my printed Gecko 1.0, I painstakingly modeled the entire blaster in Fusion360. There were three...

This model is extremely water-resistant, highly buoyant, and accelerates quickly with my setup. I printed this on my Ender 3 using split parts for easier printing or a single part if your printer can handle the height. The hatch measures 26mm deep,...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

I made 2 cover models: one is you can do multiple color layeur prints and one if you can't. The multiple color files are noted CoverBox2_colorX and the single color STL is CoverBox1.&nbsp;</p><p>If you're using multiple color layer prints, the height...

Rollerspooler is the latest in TUSH-Varientalology, using the base Idea from the original The Ultimate Spool Holder (by filamentry) then adding the Clamp from the original Prusa Spool Holder (because, why reinvent a perfectly working wheel?) to mount...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces.&nbsp;INSTRUCTIONS&nbsp;Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

I modelled all parts in Fusion 360 from scratch. ATMEGA is programmed like "Arduino on breadboard" as seen here: https://www.arduino.cc/en/Tutorial/ArduinoToBreadboard - the minimal version without external clock, running on 8 MHz. I put everything...

Here's an updated model! Some people mentioned that it was too difficult to print with certain materials as it wouldn't handle overhangs. The new update has a split version that can be printed in two separate pieces with full supports that can be...

The "Advanced_Fit" version is meant for printers with tighter tolerances and may provided better heat break cooling due to the extended cooling channel.** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided...

This model only cost 1 dollar because I am only pricing the topper and Star mount, the rest is free with the purchase. This is a pixel tree mount to build an eighteen string 216 degree pixels tree. Height can be up to 5 feet. The base design is...