mars 3d model

I designed this from scratch for my Mom's iPad 2, and it's a five-piece model that presses together perfectly. The horizontal support member is printed in two halves that have to be glued together before being placed in the upper hole of the S...

This add-on might fit on the other models this is based on like rmcht’s Double Gear Grinder and the Dual Drive system of claxly. There would be more overhang opposite the drive gear. I haven’t tried this unit on any of those. This is a simple...

My favourite one lives indoors with me: It's a (dusty - see photos!) DC14 model, and I only use it for vacuuming my flat. It's got excellent tool storage for all the bits that came with it. But, over time, I've collected a couple of extra tools I...

This custom cable wrap is specifically designed for the Dell Slim Power Adapter 65w and 90w models, which were included with some Dell Latitudes in recent years and have rounded sides (see images). It may also fit other adapters with similar shapes...

A shorter SC4U version is available and an extended SC4UU model is also provided. A stiffer version for use on the x-axis was added. Send a message if you encounter any problems or have suggestions. Using plastic bushings instead of bearings...

To get Cura to properly slice the model with minimal travel movements I enabled Optimize Wall Printing Order, Set Z Seam Alignment to User Specified and Z Seam X and Z Seam Y to 500 mm. Included Inserts Spider Web Some of My Designs Click an image...

... Lysippos around 330 BC. Alexander is shown looking upwards, as if to challenge the gods themselves. This vision of the inspired ruler, widely copied by Alexander's successors and imitators, became a standard model for Hellenistic royal portraiture.

 I experimented with adding a diffuser, but that did not solve the problem.Version 2 has instead added a baffle, which blocks the downward light and lateral leakage, only permitting light in the direction of the nozzle and of the print under the...

These design criteria, along with my limited fusion360 skills, has led to the final model posted. BILL OF MATERIALS > * 4 x Screws & Anchors (M4) https://www.amazon.ca/gp/product/B07HQ4YMYY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 ...

Give me a 🧡 if you like my work.This is an improved version of Knife Bow Stand: better parametric formulas, improved stand using sand as stability weight.CreditsMichael Whitley: Thank you very much for publishing model of Chef's Knife, which made it...

If your cable is smallerthan the frame hole, wrap some tape around it to fill the gap.2 layers [.4 nozzle]set walls to 15 for strong solid parts0 top/bottom layerssupports are built into the frame STLTolerances are tight on this model and good layer...

In this model I print between 35mm/s for initial and top layers to 40mm/s for infills and walls, and you can probably go faster after your initial layers. - Wall line count is 4. - Bottom layer count is 2. - Top Layer count is 3 - Infill Pattern...

To maintain optimal performance, I've made the normal back of the printer the front so that no belts run in front of the model. Motors are also positioned up front, with plans to cover some areas to make them safe. Currently, I'm utilizing...

This is a set of hub adapters and anti-flip brackets to use RadioShack Mattracks on Tamiya CC-01 and Traxxas TRX-4 Trucks. In addition to the models provided here, you need a set of Radio Shack Mattracks :-) These seem to be getting scarce, but...

Not just any standard improvements have been made in this model – rather, the new version truly makes the overall retract performance smoother as long as cap screws are tightened with restraint, to say the least. A considerable boost can also be...

--------------------------------------------- This is a remix of the following models. (Unfortunately I didn't manage to link it as a remix because the search doesn't work): G-Clamp fully printable by johann517 Articulating, Wall-Mounted,...

The architectural models created by the entrant teams are displayed on the eighth floor of the Harold Washington Library Center, except for the SEBUS entry, which is located in the ninth-floor Special Collections. With the support of Harold...

# _**Important:**_ Don't use the Thingiverse customizer for this model. **Use OpenSCAD** instead! --- While browsing thingiverse I came across [Sweeping 2-line name plate](https://www.thingiverse.com/thing:3045130). I didn't use it because I...

The Supports Need To Be Removed And The Hole Punched Through Supports Are In The Model And Dont Have To Be Added. Hygrometer: I Used Cheap Hygrometers From Amazon If You Have The Same Then You Can Use The Frames To Mark The Cutout And Make It Look...

... a single set rather than repeat the same figure in several sets. If I have omitted something important, message me. These models by waynemc65 are licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license. ...

I included three models: one is a solid piece, and the other is broken into two pieces with a threaded screw just in case you had problems printing the whole thing at once and the undersides of the print came out ugly. You may want to scale it up if...

The reference S23 holder model was created by thingiverse user Icepir8, licensed under gpl. Footnote: I originally intended to print the layers over a bed lined with leather to get the faux leather impression on the surfaces - hence 'foney'. I...

I have modelled in a 0.2mm tolerance on all parts, though in test printing some sanding and filing was necessary to get all pieces to fit together. The flashlight on top can be replaced with a straight combat rail as pictured. Both the base of...

I also added a second part A that works with a different model of JLab headphones that have 2 shorter rubber pieces instead of 1 longer one. I added a second picture of the new set of headphones to the images. And last I updated part C (the main...

I've included two models: one with integrated spacers and the other without. This print uses the two stock screws that held the 40mm fan on the printer, forcing fan orientation as seen in the pictures above. I recommend using a fan that can provide...

You might want to wait to glue the Shoulder_Upper_Outside_L/R pieces to the rest of the model until the gun mounts are ready. You will need to make sure the bottom slot of the Shoulder_Upper_Outside_L/R lines up with the open slot of...

This is a carrying handle for Future Motions outstanding Onewheel+ although it should fit any of the Onewheel models. If you haven't heard of a onewheel, think of a cross between a segway and a boosted board with only one wheel (duh) and no...

I've also included my blender file in case you want to change anything; I left all the raw subtractive models in it, so you could even swap the motorcycle for your own keychain design if you wanted to put a light on it. Assembly: First, decide how...

This was my 1st attempt a making a multi part model. At full size it measures approx. 7" x 4-3/8" x 13" (177.8mm x 111.13mm x 330.2mm). I now present to you all this ridiculous approx. 7:1 ratio Duracell 9V Battery Container! ;-) Printing: All...

It should work with the other X5SA models however you'll need to adapt the length of the linear rail (450mm for X5SA 400). Some advantages of this gantry and X-carriage over stock: Linear Rails are smoother and more reliable than V-Slot Wheels...