model scale conversion chart

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

... clean it up.  Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

None of these models should need any support, I try to avoid them if at all possible, but you will need to be able to bridge somewhat decently. I personally used Overture Easy Nylon, it's very stiff for a nylon that doesn't seem to creep and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

Rollerspooler is the latest in TUSH-Varientalology, using the base Idea from the original The Ultimate Spool Holder (by filamentry) then adding the Clamp from the original Prusa Spool Holder (because, why reinvent a perfectly working wheel?) to mount...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

I made a simple 3D model of the MKS SBASE board with the locations of the components I needed to be concerned with. You can use MKS_Sbase_CircuitBoard_Layout_Rev2.scad to adjust any of these that might vary for your board. I remixed this to be...

I modelled all parts in Fusion 360 from scratch. ATMEGA is programmed like "Arduino on breadboard" as seen here: https://www.arduino.cc/en/Tutorial/ArduinoToBreadboard - the minimal version without external clock, running on 8 MHz. I put everything...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

This allows protecting the model against falling over.Printing configurationLayer height 0.2mm0.4mm nozzle15% infillWhite PETG filamentplace the two halves making the bottom part of the sensor housing to their sideno support except for the top...

Instructions First make sure the nozzle diameter and layer height match your slicer's settings, as by default the model is exactly 2 nozzle-diameters thick in each slice so as to avoid generating any fill paths (which would show up when lit). Also,...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

They can compare the forces involved to what computer models predicted. d. Students can use solidworks to predict and measure stress and loading on them.<br/> e. Students can explore redesigning these to be lighter, use composite material, or have...

The idea is to loose both heat breaks, push both nozzles into the bed, then tighten the screws in both hotends to secure the heat breaks.CreditsCM3D MK3S: https://github.com/ComunidadMaker3D/CM3D-MK3SMK3...

- An increase of thickness from 0.5mm to 0.6mm, which should allow a wider variety of resolutions and nozzle sizes to print the design and make the end-products more reliable between printer models. Thank you again for your support and enthusiasm...

... to be retained and passed through, if desired. Can be nice if you want to completely remove the controllers from your hands at times without needing to set them down. Happy Printing. I would love to hear in the comments if you use this model.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

... parts outlined here. Once you are done with that, include the 3d printed parts included in this project (skipping or replacing the parts from the original design that have been redesigned here). Huge thank you to Revar for the original models!

The code you want to stop at is M107Example of first portion [to copy and paste in a new document]:; generated by PrusaSlicer 2.4.2+win64 on 2022-05-19 at 22:12:52 UTC; ; external perimeters extrusion width = 0.45mm; perimeters extrusion width =...

For more details, visit http://www.thingiverse.com/thing:47032 [^] (v.1) naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

Subscribe Now! A very good model from Multiverse3DDesigns. Remixed to support free to do timelapse. https://youtu.be/H-_2R-mKoMo <a href="https://youtu.be/H-_2R-mKoMo"><img...

For example, if you shower pole diameter measures 22mm, try a Pole_Diameter value of '21'. Material We recommend printing this holder in ABS filament for extra durability. Versions 1.0 (5 Dec 2020) - Initial version Printing Recommended slicer...

https://www.printables.com/de/model/172064-phaetus-taichi-mount-and-fanduct-w-dual-5015-fans- ________________________________________________________________________ This is an highly integrated Mount and FanDuct for the upcoming Phaetus TaiChi...

Long story short, these gears don't work in the real word unless you really really know what you're doing (like how to avoid the bending because you know your material strength properties and your torque forces and more I don't know) Support me...

Based on the code provided, it appears that you are trying to create a 3D model using Blender's API, Python, and NumPy. Here is a modified version of your code with some comments for clarity: ``` import bmesh import mathutils from numpy import...