models of terminators

... <p class="detail-setting notes"><strong>Notes: </strong> </p><div><p>All parts should be easy to print. The "RPi with ringlight" needs a print bed of 21cm or more The Diffusor/Polarizer should be printed in transparent/white PLA Category: Tools

When I look out of my window, I feel really happy. The colorful homes for bees, which I made with my 3D printer, have turned from just things in my garden into lively spots where wild bees are busy flying in and out. The bee homes are there,...

See updated photos on wiring up control switch Wiring instructions: * Brown (-) and Green (+) from the Ultrasonic mister * Green wire goes in series with the switch, comes out as the red wire, joins back to the Step Down DC-DC Module (+IN) * Brown...

Here is a TPU spacer to be used to install the really nice HEPA & Carbon Filter designed by PrinterBox [ https://www.printer-box.com/hepa-carbon-filter ] on the marvelous [Prusa] Box also from the same designer [...

Having the speed marked down during the first layer is also important to get the best foundation for the rest of the print. These are the settings I used when printing: Enable Brim foundation. Enable supports from the building plate. Shells: 3...

Printed in PETG, which has a bit of flex to it. Each shelf (4 brackets, 8 inner parts) takes about 18.5 hours to print at 0.15mm layer thickness. Shelf supports were printed with 4 perimeters and 20% infill. Inner parts are printed with 2 perimeters...

The rest of the parts print fine without any support for me. For optimal results, I recommend printing the front and back on their thinner sides (see the combined plate for the recommended position). I hope you enjoy this stand as much as I do! A...

Parts # 2 & 4 must be attached to the flat side of the hook (01) and jaw (02). Alternatively, you can print parts # 01_02 and 03_04 with supports, though this results in a less satisfactory finish that requires sanding for a smooth surface – glue is...

The diameter of the propeller is more like 184 mm, so this guard inner diameter is 188 mm. You may swap between the Propeller Guard and the Motor Stabilizer as the height to the wing mount is the same for these two parts. Dont mount the black fan...

the only thing that should need supports it the end of the arm that is next to the frame. so if you make your support angle 80* it should just make supports for that part. (I think). I printed these with 3 walls and 10% infill. print two normal and...

the cover no longer fits on it, but I had to replace the left side of the input cam with something reinforced anyway, so that the cover no longer fits on it anyway! I also put in ptfe tubes that protrude about 30 mm so that the filament can be...

Socket racks and extension trays Remix of: https://www.thingiverse.com/thing:4696546 Credit to BuildBug for concept Used these magnets: DIYMAG 2MM-Mix 100 Piece Refrigerator Magnets for Office, Hobbies, Crafts and Science, Round Ceramic Industrial...

The LED driver is placed in the middle, and the electronics lid fits snugly on top of it. The cover glides over the wallmount horizontally, making sure the guides in both parts align perfectly. A 20mm indentation at each end accommodates a 1W LED...

(You can of course extend the filament sensor cable, then you would still have the sensor active.) Assembly is pretty straightforward. However, you might get confused with all the parts in the E3D box. I used the original temperature sensor and...

BE CAREFUL NOT TO GLUE THE BATTERY IN PLACE. Wait for the glue to dry and the dock is ready to use. If you are planning on buying a whoop, use this link for a free month of service! Whoop Free Month Print Settings Printer Brand: Creality Printer: ...

The VESA bolts are M4. The iMac foot is calibrated for a certain weight of course. If you put a 30" monitor on there it will just sag; a 15" monitor will just point at the sky. ...20" is about the right weight.</p> <h3> Print Settings</h3>...

Since the plasma machine generates lots of electrical noise, the controller would constantly restart whenever the plasma was turned on. To resolve this issue, I placed the controller in a metal box and stopped communication over USB (using G-code on...

"Customized version of http://www.thingiverse.com/thing:243650 using Customizer!

... by mirroring. Holes for attaching the adapter to the GoPro mount have been added to the original rear part of the case. For the connection, you will need 2 M3*8 bolts and nuts to them. The adapter is created in two versions: male and female. ...

Separate the two wire strands and strip ~5/16" (7mm) of insulation from the ends 3. Crimp or solder the bare wire ends into the PowerPole center contacts; crimping is preferred if you have access to the proper crimper... 4. Insert the PowerPole...

Made this because I wore out two of them, and at $30 each, they are cost prohibitive. Other people have complained about the same issue (soft plastic, and thin design.</p> <p><a...

Brake Barrel Adjuster Brake Ferrule (see above section) This accepts brake barrel adjusters with a maximum threaded length of 17 mm. If yours are longer than this, they may just bottom out and you'll have "lost" some adjustment. It'll just stick out...

* [Twitter Bootstrap] - great UI boilerplate for modern web apps * [node.js] - evented I/O for the backend * [Express] - fast node.js network app framework [@tjholowaychuk] * [Gulp] - the streaming build system *...

If there's others that has any suggesstions/comments, please let me know, or modify/remix as needed. UPDATE 14FEB2019 Uploaded pictures of v2. Still need to tweak it a little bit more. Will upload the changes needed once completed and tested</p>...

This is my remix of Adarkstudio's case but with a cable chain mount. It is compatible with the Creality stock or silent board, SKR Mini E3, and EZBoard Lite.</p> <p>If you any questions or issues, I'll be sure to answer them!</p> <p>Notes:<br/> •...

In addition to the PDF, consider the clamp's formation via forge press and the use of standard store bolts in knobs. If needed, a small screw knob can be added for extra force. The base and carrier share wood composition, with similar manufacturing...

This is a Pi1541-II Case for the Backoffice Show PCB created by Stephen White for the Pi1541 software.\r\n\r\nThe design is still under development and various adjustments are needed to finalize it.\r\n\r\nThree-millimeter self-tapping screws are...

https://youtu.be/Kc2nWAM-f9g February 16th: Instead of my initial design, I made a change to the gantry. It wasn't easy to create and wasn't strong enough for milling aluminum. February 10th: I'm making progress on the project. The CNC controller...

See those in the STEP file zip folder --> "BONUS" for all of the files Printed Parts: -1x RH Duct -1x LH Duct -2x Fan Clips -1x LH Fan Bracket -1x RH Fan Bracket -BLtouch Adapter Bracket -Wire Tie -TPU Vibration Dampener insert (optional) What's...

It is also still a M10 screw needed with a length of 70-80 mm needed. I am still to construct the clamping plate so that you do not have to buy it. I can not guarantee that the plate holds on longer time since I have this only recently mounted. The...