monoprice mp10 3d models
6304 3d models found related to monoprice mp10.thingiverse
Remix of Superman889's Ender-3 Gantry Camera, modified for MonoPrice MP10.
thingiverse
A BLTouch adapter for the Monoprice MP10 & MP10 Mini. ...NOTE: you will need an open source control board to get this to work as the stock firmware on the MP10 line of products does not allow for a BLTouch.
thingiverse
Monoprice MP10 Extruder Cover German Neues Updates 1. Keine Lüftergitter mehr daher mehr Luftzufuhr, 2. Größe wurde Nachgebessert, _______________________________________ Englisch New updates 1. ...No more fan grilles, therefore more air supply, ...
thingiverse
rounded filament spool holder for monoprice mp10 fits directly over the existing metal spool holder to make it rounded with less friction no supports 20% infill
thingiverse
The part fits the 3d printer from Monoprice MP10. With this part, the filament spool is kept straight and unwound cleanly. ... It can be used for different spool widths
thingiverse
Mosquito and clone hotend carriage adapter, fan mount, fan ducts and sensor mount for the Monoprice MP10 and mini variant. This is designed to bolt directly to the carriage without the magnets but can be used with the magnetic hotend plate if you...
thingiverse
This bracket is used to attached CR10 style support rods to a Monoprice MP10 printer. In addition to this printed part, you will need 4 M3 bolts, nuts and washers and 2 M5 bolts and washers. ... The M3 nuts will be used with the following slot nut...
thingiverse
This will function as a bracket for the Monoprice MP10 to use the stock CR10 Z-brace without tapping the front frame. This is designed for M5 hardware all around. You'll need two screws M5x8, two M5 DIN125A washers, and two M5 drop-in T-nuts...
thingiverse
I could not find a replacement part for the monoprice MP10 3d printer. The contactless distance sensor was broken. The coil was broken. I found a similar replacement coil at conrad.de, but it is larger. This holder is glued to the distance sensor.
thingiverse
I got a Monoprice MP10 3D Printer and found out that is has poor strain relief on all cables. So I designed my own one for the filament feeding right at the top of the printer head. It has some legs so you just need to stick it into the head. ...A zip...
thingiverse
This is a Y-Axis Endstop adaptor modification I made for my Monoprice MP10 3d-printer. I was having a problem with Y Axis being about 30+MM off and needed it to go further back. I will use the existing Y-Axis switch, but you will need to get a...
thingiverse
A slight variation of theskyliesxx's filament holder for the Monoprice MP10, this adds a "fence" at both ends plus another at about 65mm, as that is the right width for the Inland filament spools from Microcenter and keeps them from sliding too far...
thingiverse
Had problems getting a new build film for the Monoprice MP10 Mini printer from Monoprice, I tried a sheet from Creality, it fit the steel build plate but the thickness caused the nozzle to scratch the surface. Designed a new proximity sensor holder...
thingiverse
This is an adapter to mount an E3D V6 hot end to a Monoprice MP10/Mini, by reusing the magnetic plate on which the original heatsink and hotend were bolted. The original bolts/nuts that were used can be reused by loosening them and sliding the mount...
thingiverse
I had attempted to find an existing knob for allowing easier adjustment of the MP10 print bed but could not find something that was adequate for my needs. Either the knob was too large (and thus not allowing the bed to slide between the uprights) or...
thingiverse
Until the heatbreak jammed :( I modified the base to use the stock Monoprice MP10 extruder 'arm'. It had a small screw that got in the way on the underside, so I made a huge area on the plate for clearence. I also made the 'ribs' on the side of...
thingiverse
The PTFE Bowden tube on my Monoprice MP10 (Creality CR-10 clone) wasn't well supported where it left the extruder. It drooped excessively which seemed to cause unwanted friction on the filament, so I designed this bracket to resolve the issue. ...
prusaprinters
The PTFE Bowden tube on my Monoprice MP10 (Creality CR-10 clone) wasn't well supported where it left the extruder. It drooped excessively which seemed to cause unwanted friction on the filament, so I designed this bracket to resolve the issue.</p>...
thingiverse
The stock hotend assembly with the MP10 was not the greatest in my opinion, but I do like the removeable magnetic baseplate assembly. This mount will be compatible magnetic baseplate to the x-gantry and will allow you to retrofit the more common...
thingiverse
My Monoprice MP10 (Creality CR-10 clone) fitted with an alloy MK8 Bowden Extruder upgrade would turn any soft filament into spaghetti due to the filament path floating in mid air after passing the extruder feeding gear. I designed this part to fix...
thingiverse
One mount for the BL Touch can be screwed into the same mount on the parts fan on the right of the Monoprice MP10 Mini. Since it covers part of the fan, the newer version has ducts to help with airflow. The LEFT mount fits by friction in the...
cults3d
This is the DELUXE version of the free Monoprice MP10 200x200 hot end cover. The DELUXE hot end cover features a "dual cooling system", where cool air is blown onto the melted plastic in two directions instead of just one! The more cooling, the...
prusaprinters
My Monoprice MP10 (Creality CR-10 clone) fitted with an alloy MK8 Bowden Extruder upgrade would turn any soft filament into spaghetti due to the filament path floating in mid air after passing the extruder feeding gear. I designed this part to fix...
thingiverse
Fan duck I made as I could not find a correct stl, ENJOY!!!!!
thingiverse
The default MP10 inductive sensor from my user experience is complete garbage with uneven measurements constantly going out of sync. This mount allows you to install a 5v NPN M8 thread inductive sensor into the stock inductive sensor location using...
thingiverse
An adapter plate that uses the original screw holes of the MP10 mini that places the Bigtreetech SKR Mini mainboard above the fan meant to cool the original board. ...M3 hex nuts are placed in the places with hexagon cuts with a sacrificial bridge in...
cults3d
I wanted to style my 3D printer's hot end, so I looked online for a cover for it, but I couldn't find a fit, so I designed my own! It took only two tries too! I want to design another that has a modified cooling end so it can cool two sides at a...
thingiverse
Ive recently received a Monoprice MP10 as a gift. I am an instructor and recently took a virtual instructing course due to the pandemic in an effort to continue to instruct. I had to visualize myself as newly introduced into 3D printing. Part of the...