neo qube 2 build 3d models

A standard NEMA 17 from Asia makes not more than 100/120 turns/min (12V) -> 1.x-2 turns/s -> 70-88mm/s. I don't say 300mm/s is not possible, but you need nearly 8 turns/s or 480 turns/m I'm thinking about the Diamond Nozzle and a marzipan extruder...

Bigger magnets are more likely to fit lengthwise/sideways.To be more specific: In print bed orientation (not inside-the-porcupine orientation), the inside of the insert is 0.85cm wide tapering to 0.57cm wide, 1.73 cm tall (excluding the curve), and...

The long term goal is to make this useful for a variety of boards not just Arduinos. This is version 2.0. If your looking for the original look the v1.0 release at my Github repository:<br/> <a...

Non-3D printed parts: Four 10-24 machine screws (2" or 1.5" long) (10-32 or M5 should also work) Eight 10-24 nuts (10-32 or M5 should also work) Four 13" zip ties 1/16" self adhesive cork (use thicker if your tube diameter is smaller) Four 10-24...

UPDATE 3 (regarding Wanhao Duplicator i3/i3Plus):\nI highly recommend replacing the bearing rods and generously applying MoS2 grease to the inside radius of the original linear ball bearings for maximum quietness and lower friction.\nThe greased...

These 2 items should allow you to mount the roller shade w/o using the existing iFit mounting hardware. This was designed for in window installation. To use this remix you need to remove the spring assembly from the roller shade, I included the...

1st class - debrief activity and show appropriate videos on assembly process of Hubsan X4 2nd class - disassembly process of the Hubsan X4 for each group 3rd class - 3D designing and modifying of drone frame + 3D printing them 4th class - assembling...

Made to be used with 5015 fan.Has mounting points for ADXL345 sensor&nbsp;I printed the parts with ASA&nbsp;What you will need (with links for what I used):Pancake Nema 17 motor (link)V6 Volcano hotend (link - get coated version for higher...

The best uploaded setups will become part of this description.&nbsp;when making setups you can use different size escape bricks and obstacle bricks, and you can also decide where the exit should be.Setup 1&nbsp;Setup 2&nbsp;Setup 3&nbsp;Good Luck and...

The design of this toy was inspired by Theo Jansen's Strandbeest creatures, and combines 3D printing with some custom hardware to put the beauty of Jansen's walking mechanism in your hands. Kits are available for purchase here:...

This may take quite a bit of force depending on how well your print turned out.Repeat step 2 for the lid.Use the bracket to line up and glue the backstops in place. The backstops overlap the seam of the lid, do not glue the left backstop to the right...

I used the last “big” solar eclipse (July 2nd 2019) as the reference position.Rotate (anti clockwise) the large disk of the Sun until you reach the date you want.Do no rotate too fast.&nbsp;&nbsp;Print Settings :Printed on MK3SFilament tested : PLA...

Otherwise the slider may jam in the top-plate.Assembly Instruction:&nbsp;Step 1:Lay the bottom-plate over the knob of the racket handle.Make sure that the flat surface is on top, and the opening for the knob points to the lower end of the...

 Opening the original dome requires removal of four recessed triangle head screws, which is done with a 1.8 triangle head driver (either purchased or DIY) or via a lot of messing around with a small but longish flathead precision screwdriver (one...

2. Place all of the enemy tokens into their sized boxes and place the robots, humans, super-mutants, and monster enemies into the hex insert (optional). Place those on top of the second (lower) stack of map tiles in the lower right of the box. If...

If you can't slide one into the other, try shrinking the inner box a bit (1%~) in your slicer.It must be printed with at least 2 perimeters and can be printed with 0% infill.Printed in PLA and with several months of use it only shows slight scratches...

In contrast to V4, the holes are resized to clamp some cables better.&nbsp;You need to disable skirt to print this diagonally on an Ender 3.&nbsp;Print SettingsPrinter Creality Ender 3 V2Supports: NoResolution: 0.2Infill: 10%Filament: Material4Print...

Used 2 perimeters with 10% gyroid infill. 10/06/2021 Edit Added new wheels to be used with bearings. Files with 4x8x3 bearing name modifier have slots for 4x8x3mm metric ball bearings. Files with 4x9x4 bearing name modifier have slots for...

A set of at least 2 plates can be accommodated inside the box (one in the lid and one at the bottom).My prints were all at 0.20 mm layers and with a nozzle of 0.4 mm. Some of the STL's have built in support where needed ... if there is no STL with...

After 2.5 years of use with it, the plastic broke from overtightening (totally my fault). So I searched around and landed on getting an inductive probe. I wanted one that was small and could run fast, which pretty much describes the SuperPINDA made...

The horsemen of the first group (2-7) wear a fox-hide cap, short chiton, chlamys, and boots, the second group (8-13) only chlamys. In the third group, the horsemen (14-19) wear a short cuirass over a short chiton and boots. The horsemen of the...

Depending on your printer, you may need to drill out the holes to 2.4mm prior to tapping. The deck is very flexible because there is not very much material connecting the two halves. Once the tabs are inserted into the X carriage, the fan shroud is...

That's all for now.Reddit reference thread: AtreuSLB50+Print SettingsPrinter Brand:CrealityPrinter:Ender 3Rafts:Doesn't MatterSupports:YesResolution:0.2Infill:15Filament:PLA&nbsp;Notes:&nbsp;If printed in the recommended orientation, supports are...

Basically, the overhangs curl up a bit, and if you have a really small layer height, your extruder will run into that curling in a more severe way than if it were 0.2mm layer height. How I Designed This I used AutoCAD 2016 on a laptop... Took about...

2. You'll need approximately 90cm of transparent monofilament fishing line. Cut more than this, as the ends can be trimmed later. 3. Tie a large knot in one end of the line using an improved clinch knot, which is a standard fishing knot for tying on...

https://www.larsonelectronics.com/product/144200/explosion-proof-enclosure-c1d1-24-x-30-x-8-internal-dims-surface-mount-n3rThe EPL-AEB-24.30.8 from Larson Electronics is an Explosion Proof Enclosure that provides operators with a Class I and II,...

Grooves are 1.2 mm wide and 0.6 mm deep. * `fingergroove` = finger grooves. false=no finger grooves (default). true=include (this disables `groovespc`). **Warning:** Enabling this setting causes the handle to fit **only** the hand for which it is...

The previous design for 1/2" tubing legs did not really leave enough room for internal wiring, so I've removed the .stl files for those. If anyone wants them let me know, but I would recommend 3/4" or 20mm tubing. The dome can be mounted in the X or...

... v1.1 - added a longer pointer minute/x100ft hand model to better match the appearance of the altimeter I am accustomed to. v1.2 - added a .stl model cover disc and printable PDF for text and cutting template for barber pole stripes wedge disc

To add strength, i used 3 outside walls instead the default 2. I maybe should have used more than 3 walls but it seems strong enough. I am using this in a workshop, so i want this to to tough, in case i drop it. For now, the 3 walls seems good...